Cisco ASR 9001 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 160

background image

Troubleshooting Using a Subsystem Approach

To solve a system problem, try to isolate the problem to a specific subsystem. Compare the current router
behavior with the expected router behavior. Because a startup issue is usually attributable to one component,
it is most efficient to examine each subsystem, rather than trying to troubleshoot each router component.

For troubleshooting purposes in this chapter, the router consists of these subsystems:

•

Power subsystem

—

Router chassis is shipped with up to two AC-input or DC-input power supply modules

installed in the Cisco ASR 9001 Router chassis.

•

Chassis backplane power distribution

—

System tra12 VDC power from the power modules to

the chassis backplane and distributes it to all the cards through the backplane connectors. The fan tray
receives power from the chassis backplane and communicate to the RP CAN Bus controller.

•

Processor subsystem

—

Includes the active Route Processor (RP) card with line card. The RP is equipped

with onboard processors. The RP downloads a copy of the Cisco software image to the line card processor.

•

Cooling subsystem

—

Consists of one fan tray with 14 fans, which circulate cooling air through the

chassis.

Normal Router Startup Sequence

You can generally determine when and where the router failed during the startup sequence by checking the
status LEDs on the power modules and RP.

In a normal router startup sequence, this sequence of events and conditions occur:

Procedure

Step 1

The fan in each power module receives power and begins drawing air through the power supply.
The power module input power and output power indicators are on.

Step 2

The fans in the fan tray receive power and begin drawing air through the chassis.
The fan tray OK indicator is on.

Step 3

As the power-on and boot process progresses for the RP, the status of the RP appears on the front panel of
the card.

Identifying Startup Issues

The following table shows the LED states on the power modules (AC or DC), RP, and the fan tray after a
successful system startup.

Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide

86

Troubleshooting the Installation

Troubleshooting Using a Subsystem Approach

«
...
96
97
98
99
100
...
»

Содержание ASR 9001

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 9001

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 4

Бренд: REXROTH Страницы: 68

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: Ubiquiti Страницы: 20

Бренд: AMG Systems Страницы: 2

Бренд: UfiSpace Страницы: 35

Бренд: JUMO Страницы: 60

Бренд: NBase Страницы: 18

Бренд: Gearlinx Страницы: 23

Бренд: ADTRAN Страницы: 136

Бренд: TRENDnet Страницы: 7

Бренд: Orcon Страницы: 2

Бренд: LanReady Страницы: 40

Бренд: Juniper Страницы: 230

ControlCenter-IP 2.0

Бренд: G&D Страницы: 60

ForeFront 2616RC

Бренд: Patton electronics Страницы: 80

Бренд: MasterForce Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды