Cisco ASR 14000 Series Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 132

background image

C H A P T E R

5-1

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

5

Installing and Removing Exterior Components

This chapter provides instructions for installing and removing the exterior cosmetic components on the
Cisco ASR (Aggregation Services Router) 14000 series 8-slot line card chassis. This chapter presents
the following topics:

•

Overview of the Exterior Components

•

Installing or Removing the Front Side Exterior Components

•

Installing or Removing the Rear Side Exterior Components

Overview of the Exterior Components

Exterior cosmetic components for the Cisco ASR 14000 series 8-slot line card chassis are not required
to be installed; they are provided as optional components (except for the cable management bracket,
which is preinstalled). The 8-slot line card chassis is shipped with the following exterior components:

•

Cable management bracket (shipped preinstalled on the chassis)

•

Inlet grille (shipped separately)

You can also install the optional exterior exhaust grille for the rear of the chassis. This exterior
component for the rear of the chassis does not ship automatically with the product; it must be ordered
separately.

Installing or Removing the Front Side Exterior Components

This section contains the following procedures:

•

Removing the Cable Management Bracket

•

Reinstalling the Cable Management Bracket

•

Installing the Inlet Grille

•

Removing the Inlet Grille

«
...
111
112
113
114
115
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 14000 Series

Univerge SV8100

Бренд: NEC Страницы: 44

Бренд: G-Technology Страницы: 35

Бренд: Paradyne Страницы: 85

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 8

Barricade SMC7901WBRA2

Бренд: SMC Networks Страницы: 2

Бренд: ICP DAS USA Страницы: 62

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Emotron OSTO 100

Бренд: CG Страницы: 112

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Manson Engineering Industrial Страницы: 10

Бренд: ActionTec MI424WR Страницы: 3

Бренд: Erbauer Страницы: 36

DiskStation Series

Бренд: Synology Страницы: 6

Бренд: Atlantis Land Страницы: 2

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

AT-WR4500 Series

Бренд: Allied Telesis Страницы: 264

Бренд: X-Micro Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды