Cisco ASR 14000 Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 132

background image

5-6

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 5 Installing and Removing Exterior Components

Installing or Removing the Front Side Exterior Components

Step 5

If you are replacing the previous version of the inlet grille with the new version, remove the AC rectifier
power handles that are currently installed.

a.

Use the Number 1 Phillips screwdriver to remove the two screws from each AC rectifier power
handle.

b.

Set the screws aside as you will need them to attach the new power handles.

Step 6

Use the Number 1 Phillips screwdriver to attach the left AC rectifier power handle.

Step 7

Use the screwdriver to attach the right AC rectifier power handle.

Step 8

Align and insert the hooks at the bottom of the inlet grille into the cutouts at the bottom of the chassis
casing on the front (PLIM) side of the chassis, just in front of the power modules.

Step 9

Rotate the top of the inlet grille toward the chassis, and snap it into place on the ball studs.

What to Do Next

After performing this task, you may power on the chassis. See the

“Before Powering the Chassis Up or

Down” section on page 2-8

If you are replacing the previous version of the inlet grille with the new version, you must also replace
the AC rectifier power handles with the new ones provided with the new inlet grille. These new power
handles are necessary because the old power handles do not extend through the newly designed inlet
grille. You can do this procedure with the system still running.

Removing the Inlet Grille

This section describes how to remove the inlet grille. The grille covers the power module and air intake
areas at the bottom of the front (PLIM) side of the chassis, just below the card cage (see

).

«
...
116
117
118
119
120
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 14000 Series

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

Бренд: Lanpro Страницы: 5

Бренд: N-Tron Страницы: 138

Бренд: Observint Страницы: 117

Бренд: Caimore Страницы: 79

DHI-NVR2104-P-4KS2

Бренд: Dahua Страницы: 23

Бренд: Abocom Страницы: 63

Бренд: ACTi Страницы: 12

Бренд: Quantum Страницы: 7

Бренд: Solwise Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды