background image

Replacing the Power Supply in Cisco AS5200 Universal Access Servers  3

Safety Recommendations

possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o
documento Regulatory Compliance and Safety Information (Informação de Segurança e
Disposições Reguladoras) que acompanha este dispositivo.

¡Advertencia!

Este símbolo de aviso significa peligro.  Existe riesgo para su integridad física.

Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y
familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción
de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory
Compliance and Safety Information
 (Información sobre seguridad y conformidad con las
disposiciones reglamentarias) que se acompaña con este dispositivo.

Varning!

Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till

personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med
elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar
som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information
(Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.

Safety with Electricity

Follow these guidelines when working on equipment powered by electricity:

Locate the emergency power-OFF switch in the room in which you are working. Then, if an
electrical accident occurs, you can quickly shut the power OFF.

Warning

Read the installation instructions before you connect the system to its power source.

Warning

Ultimate disposal of this product should be handled according to all national laws and

regulations.

Warning

Only trained and qualified personnel should be allowed to install or replace this

equipment.

Warning

To ensure your safety and the safety of others, be sure the power is OFF and the power

cord is unplugged before working on the router.

Disconnect all power before doing the following:

— Installing or removing a chassis

— Working near power supplies

Warning

Before working on equipment that is connected to power lines, remove jewelry (including

rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and
can cause serious burns or weld the metal object to the terminals.

Do not work alone if potentially hazardous conditions exist.

Never assume that power is disconnected from a circuit. Always check.

Содержание AS5200-PWR-AC

















Отзывы: