Cisco 807 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 44

Cisco 807 Скачать руководство пользователя страница 32

30

5.

If SIM card is present, then push the SIM card to eject it out of the slot. Install the new SIM card by pushing it into
the slot until you hear a clicking sound.

6.

Replace the protective cover and the screws.

Modems

The Cisco IR807 uses the WP7502, WP7504, and WP7601 series modems:

Installing Antennas

There are two TNC connectors on the device. The TNC connectors are used to connect to the 4G modem. The SMA
connector is for the GPS antenna.

Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor.

If the router is being mounted on a desk, orient the antennas straight up.

To attach the radio antennas to your wireless router, follow these steps:

1.

Manually screw the antenna tight to the TNC connectors on the front of the router.

2.

Orient the antennas. For optimum wireless performance, antennas should be generally perpendicular to each other.

Dual Antennas

In all cases, an antenna must be connected to the main port. It is highly recommended in order to achieve optimal
performance that a second antenna is connected to the diversity port:



Sierra Wireless WP7xxx modem series supports SIMO on LTE. WCDMA UMTS HSPA DC-HSPA+ is diversity only,
without SIMO.

Product

Carrier/Region

Modem
Used

4G/LTE Bands
Supported

3G UMTS
Bands
Supported

2G
GSM/CDMA
Bands
supported

IR807-LTE-GA-K9

EMEA

WP7502

1, 3, 7, 8, 20

1, 8

E-GSM 900
DCS 1800

IR807-LTE-NA-K9

North
America/AT&T

WP7504

2, 4, 5, 12, 17,
25, 26

2, 4, 5

CDMA
BC0,
BC1
BC1-

IR807-LTE-VZ-K9

Verizon, USA

WP7601

4, 13

N/A

N/A

«
...
30
31
32
33
34
...
»

Содержание 807













































Отзывы:

Нет отзывов