Cisco 7000 and 7507 LED Board MAS-7KLED Скачать руководство пользователя страница 15

Страница: 15 / 20

Cisco 7000 and Cisco 7507 LED Board Replacement Instructions 15

Translated Safety Warnings

Following are translations of the safety warnings that appear throughout this publication:

Lightning Activity Warning

Warning

Do not work on the system or connect or disconnect cables during periods of lightning

activity.

Waarschuwing

Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te

werken of kabels aan te sluiten of te ontkoppelen.

Varoitus

Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.

Attention

Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.

Warnung

Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine

ab, wenn es gewittert.

Avvertenza

Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con

fulmini.

Advarsel

Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller

lyner.

Aviso

Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo

(trovoada).

¡Advertencia!

No operar el sistema ni conectar o desconectar cables durante el transcurso de

descargas eléctricas en la atmósfera.

Varning!

Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.

Chassis Warning—Disconnecting Telephone-Network Cables

Warning

Before opening the chassis, disconnect the telephone-network cables to avoid contact

with telephone-network voltages.

Waarschuwing

Voordat u het frame opent, dient u de verbinding met het telefoonnetwerk te

verbreken door de kabels te ontkoppelen om zo contact met telefoonnetwerk-spanningen te
vermijden.

Varoitus

Vältä joutumista kosketuksiin puhelinverkostojännitteiden kanssa irrottamalla

puhelinverkoston kaapelit ennen asennuspohjan aukaisemista.

Attention

Avant d'ouvrir le châssis, débrancher les câbles du réseau téléphonique afin d'éviter tout

contact avec les tensions d'alimentation du réseau téléphonique.

Warnung

Bevor Sie das Chassis öffnen, ziehen Sie die Telefonnetzkabel aus der Verbindung, um

Kontakt mit Telefonnetzspannungen zu vermeiden.

Avvertenza

Prima di aprire il telaio, scollegare i cavi della rete telefonica per evitare di entrare in

contatto con la tensione di rete.

Содержание 7000 and 7507 LED Board MAS-7KLED





















Результаты поиска

Содержание 7000 and 7507 LED Board MAS-7KLED

Отзывы:

Похожие инструкции для 7000 and 7507 LED Board MAS-7KLED

Бренды по названию

Популярные бренды

Cisco 7000 and 7507 LED Board MAS-7KLED, Инструкция по замене

Результаты поиска

Содержание 7000 and 7507 LED Board MAS-7KLED

Отзывы:

Похожие инструкции для 7000 and 7507 LED Board MAS-7KLED

Бренды по названию

Популярные бренды