CIS VCC-12CL1M, Техническое описание и руководство по эксплуатации

Страница: 5 / 30

VCC-12CL1M Rev. 900-795-35-00
©2016 CIS Corporation. All rights reserved.
5
4.
Cautions
4.1. Camera output mode
This camera enable to set Medium/Full/10Tap Configuration mode output with a camera mode and 0
～
+12dB
with a Gain.
However, fix noise in +12dB at medium Configuration might be visible depending on the ambient temperature etc.
Setting a Gain 6dB at Medium Configuration mode is recommended.
4.2. PoCL (Power over Camera Link)
This camera is supporting PoCL (Power over Camera Link), and requires power supply by two Camera Link cable. Please
check that the connected frame grabber board is capable of supplying the power by both Base side and the Medium / Full side.
If the frame grabber board is not supporting the PoCL, supply power from the 12-pin connector is required.
5.
Specification
5.1. General Specification
(1) Image Sensor Sensor Type
Diagonal Length 23.5mm, Global Shutter 4/3 type, B/W CMOS
Effective Resolution 4000(H) x 3000(V)
Unit cell size
4.7
μ
m(H) x 4.7
μ
m(V)
Image circle
φ
23.5mm
(2) Video Output Frequency
Pixel Clock 72 MHz
Medium
Configuration Mode: Horizontal frequency: 71.287kHz Horizontal clock 1010
Vertical frequency: 22.58Hz Scanning lines 3156
Full, 8Tap10Bit
Configuration Mode: Horizontal frequency: 138.461kHz Horizontal clock 520
Vertical frequency:
43.87Hz Scanning lines 3156
10Tap
Configuration Mode: Horizontal frequency: 173.076kHz Horizontal clock 416
Vertical frequency:
54.84Hz Scanning lines 3156
(3) Sync. System Internal Sync. System.
(4) Video Output Medium Configuration
Full Configuration(factory settings)
10Tap8Bit Configuration
8Tap10Bit Configuration
(5) Resolution 3000 TV Lines
(6) Output Format Camera Link output 8bit/10bit/12bit (Fixed to 8bit at 10Tap mode) B/W output
(7) Sensitivity F5.6 400lx (at Shutter speed 1/43s (OFF), Gain 0dB, and Full Configuration mode)
(8) Minimum illumination F2.8 7.0 lx (at Shutter speed 1/43s (OFF), Gain +12dB, and Full Configuration mode)
(9) Dust or stains in optical system No dust or stain shall be detected on the testing screen with setting the camera aperture at F16.
(10) Power requirements DC+12V±10% with 12pins circular connector
(11) Power consumption 6.1W ( Full Configuration mode, Full frame scan output): Factory settings
8.0W ( 10Tap Configuration mode, Partial scan 100 lines output)
(12) Dimensions
Refer to overall dimension drawing. (H:65mm W:65mm D:50mm excluding projection)
(13) Weight Approx. 270g
(14) Lens mount M42 Mount * Refer to overall dimension drawing.
(15) Optical axis accuracy Refer to drawing for CMOS Optical Axis Accuracy.
(16) Gain variable range 0dB
～
+12dB (Guaranteed range)
(17) Shutter speed variable range OFF
～
1/34000s (at Trigger mode and 10Tap Configuration)
(18) Trigger shutter mode Fixed Shutter Trigger Mode/ Pulse Width Shutter Trigger Mode
(19) Partial Scan Full frame scan
～
2 lines(2 lines/step)
(20) Safety/Quality standards UL: Conform to UL Standard including materials and others.
CE: EN55022:2010(ClassA) for Emission
EN61000-6-2:2005 for Immunity
RoHS: Conform to RoHS.