background image

OPERATION GUIDE

OG_STD-601B_v40e

Circuit Design, Inc.

18

10.10 "@R" RSSI acquisition

(enabled only in the reception)

Reads out the RSSI level.
Input

'@R'

only without the value.

Example: Reads out the RSSI level.

Control command: @R
Control response: *R64

The absolute value of the RSSI level is returned in hexadecimal.
The RSSI level can be obtained by decimalizing the value part of the control response and
adding "- (minus)" . *R64 is -100 dBm.

* If the '@R' command is issued in any state other than reception, the error response '*E01* will be

returned.

10.11 "@K" Image rejection calibration

Performs calibration on the image rejection of the receiver part. Calibration is required if the
temperature changes more than 20 °C .

If there is a temperature change of more than 20 °C after the last calibration, the error response '*E10'
is returned and High level is output at the INT terminal to warn of the need for calibration. It takes
about 120 ms for calibration.

Example: Performs the image rejection calibration

Control command: @K
Control response: *K

* Even if calibration is not performed, the receiver sensitivity will be maintained but the receiver

characteristics against the image frequency of ' RX frequency - IF-IF (RX frequency-937.5 kHz)' may
be degraded.

Содержание STD-601





























Отзывы: