CIRCLE FITNESS M8 LED Скачать руководство пользователя

Страница: 25 / 66

Document: Service Manual

Description: Treadmill

Model: M8 LED

Page: 25 of 66

Release Date: 2017/12

5.6 Troubleshooting the Treadmill

SYMPTOM

CAUSE

SOLUTION

Console display
does not illuminate.

A).No power to treadmill.

B).Console wire is not

connected or incompletely.

C).Overload, protecting is

started.

D).Console power source

damaged.

A).Check the on-off switch is on, switch

indicator shall be light. If not light,
check AC power source.

B).Check console wire every connector

points connect correctly, including
outward and connector point insert
PINs.

C).Check fuse(near on-off switch) is

worked or not, if worked, push it
back, and restart again, if work
please maintenance the running belt
and deck.

D).Turn off power then open the motor

cover, turn on the power and check
the console power pilot lamp(LED2)
where on the interface PCB, it shall
be light completely, if not, replace it.

(Refer to Chapter 5.3.1 on next

page.)

Display not
completely.

A).Console is damaged.

B).Console source power is

unstable.

A).Replace the console PCB.

B).Check the power source, turn off

power then open the motor cover.
Turn on the power and check the
console power pilot lamp (LED1)
where on the interface PCB, it shall
be light completely, if not, replacing
it.

Содержание M8 LED



































































Результаты поиска

Содержание M8 LED

Отзывы:

Похожие инструкции для M8 LED

Бренды по названию

Популярные бренды

CIRCLE FITNESS M8 LED, Руководство по обслуживанию

Результаты поиска

Содержание M8 LED

Отзывы:

Похожие инструкции для M8 LED

Бренды по названию

Популярные бренды