CIRCLE FITNESS M8 LED Скачать руководство пользователя

Страница: 2 / 66

Document: Service Manual

Description: Treadmill

Model: M8 LED

Page: 2 of 66

Release Date: 2017/12

TABLE OF CONTENTS

PREFACE

....................................................................................................................................................................... 4

1. INFORMATION FOR COMPONENTS & SYSTEM

.......................................................................................... 5

1.1 System wiring diagram ................................................................................................................................................. 5

1.2 Inverter ........................................................................................................................................................................... 6

1.3 Console PCB ................................................................................................................................................................. 8

2. ERROR MESSAGES AND SOLUTIONS

........................................................................................................... 10

3. ENGINEERING MODE

.......................................................................................................................................... 14

3.1 Engineering Mode 1: Information .............................................................................................................................. 14

3.2 Engineering Mode 2: Settings .................................................................................................................................... 15

3.3 Engineering Mode 3: Lock Function .......................................................................................................................... 17

4. INVERTER AND EXTERNAL CONTROL KEYPAD

........................................................................................ 18

4.1 External Keypad Connection and Moniter Mode ...................................................................................................... 18

4.2 Use External Key Pad to Control: Start/ Stop/ Accelerate/ Slow down ................................................................... 19

4.3 Use external Key Pad to to Control: Incline ............................................................................................................... 20

5. MAINTENANCE

.................................................................................................................................................... 21

5.1 General Maintenance .................................................................................................................................................. 21

5.2 Running belt and running deck lubrication ................................................................................................................ 21

5.3 How to spray silicone on deck ................................................................................................................................... 22

5.4 Preventive Maintenance Schedule............................................................................................................................. 23

5.5 Running Belt/Deck Maintenance Schedule ............................................................................................................... 24

5.6 Troubleshooting the Treadmill ................................................................................................................................... 25

6. PART REPLACEMENT GUIDE

.......................................................................................................................... 27

6.1 Toolkits & Components Required .............................................................................................................................. 27

6.2 Drive Belt Replacement .............................................................................................................................................. 28

6.3 Drive Motor Replacement ........................................................................................................................................... 33

6.4 Running Belt Replacement ......................................................................................................................................... 37

6.5 M8 Treadmill Side Rails Replacement ....................................................................................................................... 42

6.6 Remove and Replace the Quick Shift and Adjust the Tightness .............................................................................. 47

6.7 Align the Quick Shift to Central Position ................................................................................................................... 51

6.8 Panel of Console Replacement .................................................................................................................................. 52

6.9 Emergency Stop Replacement ................................................................................................................................... 54

Содержание M8 LED



































































Результаты поиска

Содержание M8 LED

Отзывы:

Похожие инструкции для M8 LED

Бренды по названию

Популярные бренды

CIRCLE FITNESS M8 LED, Руководство по обслуживанию

Результаты поиска

Содержание M8 LED

Отзывы:

Похожие инструкции для M8 LED

Бренды по названию

Популярные бренды