manualshive.com logo in svg

Cinterion PVS8, Обзор аппаратного интерфейса

Поделиться
Скачать
Cinterion PVS8 Скачать руководство пользователя страница 27

PVS8 Hardware Interface Overview

5.1 CDMA Antenna Interface

29

PVS8_HIO_v03.000a

Page 27 of 37

2013-04-08

Confidential / Preliminary

5.1.1

Antenna Installation

The antenna is connected by soldering the antenna pads and their neighboring ground pads
directly to the application’s PCB.

The distance between the antenna pads and their neighboring GND pads has been optimized
for best possible impedance. To prevent mismatch, special attention should be paid to these
pads on the application’ PCB.

The wiring of the antenna connection, starting from the antenna pad to the application’s anten-
na should result in a 50

 line impedance. Line width and distance to the GND plane need to

be optimized with regard to the PCB’s layer stack. 

To prevent receiver desensitization due to interferences generated by fast transients like high
speed clocks on the external application PCB, it is recommended to realize the antenna con-
nection line using embedded Stripline rather than Micro-Stripline technology. 

For type approval purposes, the use of a 50

 coaxial antenna connector (U.FL-R-SMT) might

be necessary. In this case the U.FL-R-SMT connector should be placed as close as possible
to PVS8‘s antenna pad.

Содержание PVS8






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды