CID 11-20 GPM Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

CID 11-20 GPM Series Скачать руководство пользователя страница 30

Standard & Heavy Duty Brush Cutters

January 2021

30

4.5 Blade Holder Installation

Standard Duty Brush Cutter Installation Procedure

Use a hoist, lift table or forklift to support the blade holder during
installation.

4.6 Blade Removal

1. Align the hole in the blade holder to the gearbox shaft and fully seat

the holder onto the shaft.

2. Tap the blade holder with a rubber hammer to ensure full

engagement. The blade holder must be properly aligned and seated on
the gearbox shaft spline before proceeding to the next step.

3. Install castle nut, cotter pin and cap.

Cutter blades are sharp and could cut you if mishandled. ALWAYS wear
protective gloves and footwear when handling cutter blades.

Heavy Duty Brush Cutter Installation Procedure

1. Align the hole in the blade holder to the gearbox shaft and fully seat

the holder onto the shaft.

2. Tap the blade holder with a rubber hammer to ensure full

engagement. The blade holder must be properly aligned and seated on
the gearbox shaft spline before proceeding to the next step.

3. Install six bolts and six washers, then torque per the torque values on

page 34.

«
...
28
29
30
31
32
...
»

Содержание 11-20 GPM Series





















































Отзывы:

Нет отзывов