CIBIN KUMA Скачать руководство пользователя страница 7

59

GB

The machine should be positioned in the cold room by a qualified technician and following the steps (A....E) given below. Tools 

required are as follows: -hand saw; -screwdriver; drill.

A) ASSEMBLE 

the cold room flooring, outer walls and ceiling elements which are not in the vicinity of the area where the 

machine is to be installed.

B) MAKE 

the necessary cuts and holes in the cold room panel, by respecting the formats given in the template (see Manual 2).

C) POSITION 

the machine at the prepared place. Take care to balance of the machine.

D) INSULATE 

the cuts using filler or silicone and assemble the supplied frames (if they are provided).

E) INSTALL 

the possible accessories (cold room light, door resistor, door microswitch, compensation valve, strip doors) 

in the best position for use.

If it’s provided, we advise you to connect the overflow pipe of the condensation tray to a flexible hose for water drainage.

WARNING!! 

This machine has not been designed for installation in environments with a potentially explosive atmosphere.

1.2.3 COLD ROOM LIGHT INSTALLATION 

(pre-set machines only)

Install the cold room interior light (supplied) in a position that will guarantee the best visibility inside the cold room. The tools 

required for installation are as follows: -screwdriver; scissors; -drill.

A) FIX

 the light fitting on the ceiling or wall of the cold room using the self-tapping screws provided 

 

 (fig 1.2.3.a). If the light 

fitting is being fitted to the cold room wall, ensure that the cable leads downwards, as shown.

B) REMOVE 

the glass and protective grid from the light fitting by loosening the locking screw. Make a hole for the cable throu-

gh the stopper 

 

.

C) MAKE

 a hole through the membrane of the cable gland 

 most suited to the installation type. Feed the cable marked “LC” (if 

it’s provided) from the machine through the stopper 

  

and the cable gland 

. Pull out any excess cable (fig.1.2.3.b).

D) CUT

 the cable down to size, remove the sheathing from the conductors and connect them to the relative terminals of the light 

fitting. Screw the stopper 

 

 to the cable gland and the light bulb (supplied) into the light fitting. Replace the light fitting glass 

and protection grid.

Fig. 1.2.3.a

Fig. 1.2.3.b

500mm

500mm

200mm

200mm

500mm

1000mm

1000mm

Fig. 1.2.2.a

Fig. 1.2.2.b

Содержание KUMA



















Отзывы: