dIXEL
Installing and Operating Instructions
1592027320
1592027320 XW20LS RTC GB r1.0 10.07.2008.doc
XW20LS
2/5
3.
Use “
UP
” or “
DOWN
” to change its value.
4.
Press “
SET
” to store the new value and move to the following parameter.
To exit
: Press
SET + UP
or wait 15s without pressing a key.
NOTE
: the set value is stored even when the procedure is exited by waiting the time-out to expire.
6.6
THE HIDDEN MENU
The hidden menu Includes all the parameters of the instrument.
6.6.1 HOW TO ENTER THE HIDDEN MENU
1.
Enter the Programming mode by pressing the
Set
+
n
keys for 3s (the “
°C” or “°F”
LED starts
blinking).
2.
Released the keys, then push again the Set+
n
keys for more than 7s. The Pr2 label will be
displayed immediately followed from the HY parameter.
NOW YOU ARE IN THE HIDDEN MENU.
3.
Select the required parameter.
4.
Press the “
SET
” key to display its value
5.
Use
o
or
n
to change its value.
6.
Press “
SET
” to store the new value and move to the following parameter.
To exit
: Press
SET +
o
or wait 15s without pressing a key.
NOTE1:
if none parameter is present in Pr1, after 3s the “noP” message is displayed. Keep the keys
pushed till the Pr2 message is displayed.
NOTE2
: the set value is stored even when the procedure is exited by waiting the time-out to expire.
6.6.2 HOW TO MOVE A PARAMETER FROM THE HIDDEN MENU TO THE
FIRST LEVEL AND VICEVERSA.
Each parameter present in the HIDDEN MENU can be removed or put into “THE FIRST LEVEL”
(user level) by pressing
“SET +
n
”
.
In HIDDEN MENU when a parameter is present in First Level the decimal point is on.
6.7
HOW TO LOCK THE KEYBOARD
1.
Keep pressed for more than 3 s the
UP
+
DOWN
keys.
2.
The “POF” message will be displayed and the keyboard will be locked. At this point it will be
possible only to see the set point or the MAX o Min temperature stored
3.
If a key is pressed more than 3s the “POF” message will be displayed.
6.8
TO UNLOCK THE KEYBOARD
Keep pressed together for more than 3s the
o
and
n
keys, till the
“Pon”
message will be
displayed.
6.9
THE CONTINUOUS CYCLE
When defrost is not in progress, it can be activated by holding the “
o
” key pressed for about 3
seconds. The compressor operates to maintain the “
ccS
” set point for the time set through the “
CCt
”
parameter. The cycle can be terminated before the end of the set time using the same activation key
“
o
” for 3 seconds.
6.10
THE ON/OFF FUNCTION
With “
onF = oFF
”, pushing the
ON/OFF
key, the instrument is switched off. The
“OFF”
message is displayed. In this configuration, the regulation is disabled.
To switch the instrument on, push again the ON/OFF key.
WARNING: Loads connected to the normally closed contacts of the relays are always
supplied and under voltage, even if the instrument is in stand by mode.
7.
PARAMETERS
rtc Real time clock menu (only for controller with RTC):
to set the time and date and defrost
start time.
REGULATION
Hy Differential
: (0,1 ÷ 25,5°C / 1÷255 °F) Intervention differential for set point. Compressor Cut IN
is Set Point + differential (Hy). Compressor Cut OUT is when the temperature reaches the set
point.
LS Minimum set point:
(- 50°C÷SET/-58°F÷SET): Sets the minimum value for the set point.
US Maximum set point:
(SET÷110°C/ SET÷230°F). Set the maximum value for set point.
Ot Thermostat probe calibration
: (-12.0÷12.0°C; -120÷120°F) allows to adjust possible offset of
the thermostat probe.
P2P Evaporator probe presence: n
= not present:
y=
present:
OE Evaporator probe calibration:
(-12.0÷12.0°C; -120÷120°F). allows to adjust possible offset of
the evaporator probe.
P3P Third probe presence (P3): n
= not present:, the terminals operate as digital input.;
y=
present:, the terminals operate as third probe.
O3 Third probe calibration (P3):
(-12.0÷12.0°C; -120÷120°F). allows to adjust possible offset of
the third probe.
OdS Outputs activation delay at start up:
(0÷255min) This function is enabled at the initial start up
of the instrument and inhibits any output activation for the period of time set in the parameter.
AC Anti-short cycle delay
: (0÷50 min) minimum interval between the compressor stop and the
following restart.
rtr Percentage of the second and first probe for regulation (0÷100; 100 = P1, 0 = P2 ):
it
allows to set the regulation according to the percentage of the first and second probe, as for the
following formula (rtr(P1-P2)/100 + P2).
CCt Compressor ON time during continuous cycle:
(0.0÷24.0h; res. 10min) Allows to set the
length of the continuous cycle: compressor stays on without interruption for the CCt time. Can be
used, for instance, when the room is filled with new products.
CCS Set point for continuous cycle:
(-50÷150°C) it sets the set point used during the continuous
cycle.
COn Compressor ON time with faulty probe:
(0÷255 min) time during which the compressor is
active in case of faulty thermostat probe. With COn=0 compressor is always OFF.
COF Compressor OFF time with faulty probe:
(0÷255 min) time during which the compressor is
OFF in case of faulty thermostat probe. With COF=0 compressor is always active.
CH Type of action:
CL = cooling; Ht = heating.
DISPLAY
CF Temperature measurement unit:
°C=
Celsius;
°F
=Fahrenheit. WARNING: When the
measurement unit is changed the SET point and the values of the parameters Hy, LS, US, Ot,
ALU and ALL have to be checked and modified if necessary).
rES Resolution (for °C)
: (in = 1°C; dE = 0.1 °C) allows decimal point display.
Lod Instrument display
: (P1; P2, P3, P4, SET, dtr): it selects which probe is displayed by the
instrument:
P1
= Thermostat probe;
P2
= Evaporator probe;
P3
= Third probe(only for model
with this option enabled);
P4
= NOT SET IT,
SET
= set point;
dtr
= percentage of visualization.
rEd X- REP display (
optional
)
: (P1; P2, P3, P4, SET, dtr): it selects which probe is displayed by
X- REP:
P1
= Thermostat probe;
P2
= Evaporator probe;
P3
= Third probe(only for model with
this option enabled);
P4
= NOT SET IT,
SET
= set point;
dtr
= percentage of visualization.
dLy Display delay:
(0 ÷20.0m; resul. 10s) when the temperature increases, the display is updated
of 1 °C/1°F after this time.
dtr Percentage of the second and first probe for visualization when Lod = dtr (0÷100; 100 =
P1, 0 = P2 ): if Lod = dtr
it allows to set the visualization according to the percentage of the
first and second probe, as for the following formula (dtr(P1-P2)/100 + P2).
DEFROST
EdF Defrost mode (only for controller with RTC):
rtc
=
Real Time Clock mode
. Defrost time
follows
Ld1÷Ld6
parameters on workdays and
Sd1÷Sd6
on holidays.
in
=
interval mode
. The defrost starts when the time “
Idf
” is expired.
dFP Probe selection for defrost termination: nP
= no probe;
P1
=thermostat probe;
P2 =
evaporator probe;
P3
=configurable probe;
P4
= NOT SET IT.
dtE Defrost termination temperature
: (-50÷50 °C/ -58÷122°F) (Enabled only when EdF=Pb) sets
the temperature measured by the evaporator probe, which causes the end of defrost.
IdF Interval between defrost cycles
: (0÷120h) Determines the time interval between the
beginning of two defrost cycles.
MdF (Maximum) length for defrost
: (0÷255min) When
P2P = n
, (not evaporator probe: timed
defrost) it sets the defrost duration, when
P2P = y
(defrost end based on temperature) it sets
the maximum length for defrost.
dFd Temperature displayed during defrost
: (
rt
= real temperature;
it
= temperature at defrost
start;
SEt
= set point;
dEF
= “dEF” label)
dAd MAX display delay after defrost
: (0÷255min). Sets the maximum time between the end of
defrost and the restarting of the real room temperature display.
ALARMS
ALP Probe selection for alarm
:
nP
= no probe, the temperature alarms are disabled;
P1 =
Probe 1
(Thermostat probe);
P2 =
Probe 2 (evaporator probe);
P3 =
Probe 3 (display probe);
P4 =
NOT
SET IT.
ALC Temperature alarms configuration:
(Ab; rE)
Ab
= absolute temperature: alarm temperature is given by the ALL or ALU values.
rE
=
temperature alarms are referred to the set point. Temperature alarm is enabled when the
temperature exceeds the “SET+ALU” or “SET-ALL” values.
ALU MAXIMUM temperature alarm
: (SET÷110°C; SET÷230°F) when this temperature is reached
the alarm is enabled, after the “ALd” delay time.
ALL Minimum temperature alarm
: (-50.0 ÷ SET °C; -58÷230°F when this temperature is reached
the alarm is enabled, after the “ALd” delay time.
AFH Differential for temperature alarm recovery:
(0,1÷25,5°C; 1÷45°F) Intervention differential
for recovery of temperature alarm.
ALd Temperature alarm delay
: (0÷255 min) time interval between the detection of an alarm
condition and alarm signalling.
dAo Exclusion of temperature alarm at start-up
: (from 0.0 min to 23.5h) time interval between the
detection of the temperature alarm condition after instrument power on and alarm signalling.
CONDENSER TEMPERATURE ALARM
AP2 Probe selection for temperature alarm of condenser: nP
= no probe;
P1
=thermostat probe;
P2 =
evaporator probe;
P3
=configurable probe;
P4
= NOT SET IT.
AL2 Low temperature alarm of condenser
:
(-55÷150°C) when this temperature is reached the
LA2 alarm is signalled, possibly after the Ad2 delay.
Au2 High temperature alarm of condenser
:
(-55÷150°C) when this temperature is reached the
HA2 alarm is signalled, possibly after the Ad2 delay.
AH2 Differential for temperature condenser alarm recovery
:
(0,1÷25,5°C; 1÷45°F)
Ad2 Condenser temperature alarm delay
: (0÷255 min) time interval between the detection of the
condenser alarm condition and alarm signalling.
dA2 Condenser temperature alarm exclusion at start up
: (from 0.0 min to 23.5h, res. 10min)
bLL Compressor off with low temperature alarm of condenser
:
n = no:
compressor keeps on
working
; Y = yes,
compressor is switched off till the alarm is present, in any case regulation
restarts after AC time at minimum.
AC2 Compressor off with high temperature alarm of condenser
:
n = no:
compressor keeps on
working
; Y = yes,
compressor is switched off till the alarm is present, in any case regulation
restarts after AC time at minimum.
DIGITAL INPUT
i1P Digital input polarity: oP:
the digital input is activated by opening the contact;
CL:
the digital
input is activated by closing the contact.
i1F Digital input configuration: EAL
= external alarm: “EA” message is displayed;
bAL
= serious
alarm “CA” message is displayed.
PAL
= pressure switch alarm, “CA” message is displayed;
dor
= door switch function;
dEF
= activation of a defrost cycle;
AUS
=not enabled;
Htr
= kind of
action inversion (cooling – heating);
FAn
=
not set it; ES
=
Energy saving;
HdF
=
Holiday
defrost (enable only with RTC);
onF =
to switch the controller off.
did
(0
÷
255 min)
with
i1F= EAL or i1F = bAL digital input alarm delay (1-3):
delay between the
detection of the external alarm condition and its signalling.
with
i1F= dor: door open signalling delay
with i1F= PAL: time for pressure switch function:
time interval to calculate the number of
the pressure switch activation.
nPS Pressure switch number:
(0
÷
15) Number of activation of the pressure switch, during the “
did
”
interval, before signalling the alarm event (i1F= PAL).
If the nPS activation in the did time is reached, switch off and on the instrument to
restart normal regulation.
odc Compressor status when open door:
no,
Fan
= normal;
CPr, F_C
= Compressor OFF.
rrd Outputs restart after doA alarm: no=
outputs not affected by the doA alarm;
yES =
outputs
restart with the doA alarm.
HES Temperature increase during the Energy Saving cycle:
(-30,0°C
÷
30,0°C) it sets the increasing value of the set point during the Energy Saving cycle.
TO SET CURRENT TIME AND WEEKLY HOLIDAYS (ONLY FOR MODELS WITH RTC)
Hur Current
hour
(0 ÷ 23 h)
Min Current
minute
(0 ÷ 59min)
