manualshive.com logo in svg

Churchill Nano Link IP67, Техническое руководство, Страница: 10 / 42

Поделиться
Скачать
Churchill Nano Link IP67 Скачать руководство пользователя страница 10

Page 8 

3.3.2  Universal Mains Power Supply 

An internal mains power pack can be fitted, which derives a 5.3V supply from any input in the range 80…260VAC.  
The supply includes rechargeable Ni-Cad batteries, which will support the unit in the event of a mains power failure. 

Nano_Link

 monitors the battery voltage as an analogue value that can be read by the base-station, and generates a 

digital alarm if it drops below a defined level.  If a mains fail indication is required a mains-operated relay can be used 
externally, with its contacts connected to one of 

Nano_Link

’s digital inputs.  The period for which the batteries will 

support 

Nano_Link

 depends on the mode of operation, but will typically be at least 8 hours. 

The power supply is double insulated, so does not require a safety earth.  The power input is through a two-part screw 
connector that is different both in size and colour from all other terminals, to ensure it cannot be incorrectly fitted. 

Mains power should be used for any 

Nano_Link

 used as a base-station, a repeater or an outstation that is interrogated 

continuously, used analogue or digital outputs or is fitted with expansion modules.  It can also be used for an outstation 
that is interrogated relatively infrequently. 

3.3.3  External 12/24VDC Source 

Two variants of this supply are available, one operating from a supply in the range 8…16VDC and the other for 
16…32VDC.  They are intended for operation from station supplies of nominally 12V and 24V respectively.  If the 
user wishes to monitor the battery voltage, and/or generate a battery low alarm, the 7041 Solar Power Controller 
described below can be used by connecting the station battery to it and omitting the solar panel. 

3.3.4 Solar Supply 

Solar power requires an external solar panel, a solar controller and a lead-acid battery.  The battery is required to 
maintain the system overnight and during bad weather.  Its size has to be calculated, along with that of the solar panel, 
to ensure that the system continues operation throughout the year.  Factors influencing the size of the panel and battery 
include the electrical load, the location and the ambient temperature range.  The controller ensures that the battery is not 
overcharged during bright sunlight, and does not discharge into the panel at night. 

Nano_Link

 ‘s supplied for solar operation are fitted with an internal 12VDC power supply, and use an external 7041 

Solar Power Controller and battery.  The controller is fitted in a small housing that clips onto DIN rail adjacent to 

Nano_Link

.  The battery is normally fitted at the bottom of the enclosure.  An important feature of the 7041 Solar 

Power Controller is its very low internal power dissipation.  Some commercially-available solar controllers are 
designed for us with large solar panels and batteries, and consume more current than 

Nano_Link

!  They therefore 

significantly reduce battery life when used on small systems. 

As well as controlling charge to the battery, the 7041 Solar Power Controller also provides a digital Battery Low Alarm 
output that can be connected directly to one of the digital inputs on 

Nano_Link

.  There is also a voltage monitor which 

provides a level of 0…100mV for a battery voltage range of 0…20V.  This output can be connected to one of the 
analogue inputs on 

Nano_Link

 if required. 

The 7041 Solar Power Controller has two LEDs, marked ‘Charging’ and ‘Charged’.  The Charging LED flashes when 
the battery is being charged by the solar panel.  If the battery attains a fully-charged state the ‘Charged’ LED lights, and 
the controller shorts out the solar panel to prevent further charging.  In the quiescent state both LEDs will flash 
alternately as a trickle charge is fed to the battery to maintain equilibrium. 

Whenever the solar panel is not charging the battery (e.g. at night) the Charged LED will flash and the Charging LED 
will remain off.  If the battery voltage drops below 11V the flash rate will slow to about 1 pulse/second and the Battery 
Low Alarm will be generated. 

 

Содержание Nano Link IP67











































Отзывы:

Нет отзывов