Chrysler Pacifica Hybrid 2018 Скачать руководство пользователя | Manualshive

Страница: 350 / 617

background image

•

The ParkSense Active Park Assist system will allow a
maximum of six shifts between DRIVE and REVERSE. If
the maneuver cannot be completed within six shifts, the
system will cancel and the instrument cluster display
will instruct the driver to complete the maneuver manu-
ally.

The ParkSense Active Park Assist system will only operate
and search for a parking space when the following condi-
tions are present:

•

The gear position is in DRIVE.

•

The ignition is in the RUN position.

•

The ParkSense Active Park Assist switch is activated.

•

The driver’s door is closed.

•

The liftgate is closed.

•

Vehicle speed is less than 15 mph (25 km/h).

NOTE:

If the vehicle is driven above approximately

15 mph (25 km/h), the instrument cluster display will
instruct the driver to slow down. If the vehicle is driven
above approximately 18 mph (30 km/h), the system will
cancel. The driver must then reactivate the system by
pushing the ParkSense Active Park Assist switch.

•

The outer surface and the underside of the front and rear
fascias/bumpers are clean and clear of snow, ice, mud,
dirt or other obstruction.

When pushed, the LED on the ParkSense Active Park
Assist switch will blink momentarily, and then the LED
will turn off if any of the above conditions are not present.

Parallel Parking Space Assistance Operation/
Display

When the ParkSense Active Park Assist system is enabled
the “Active ParkSense Searching - Push OK for Perpen-
dicular Park” message will appear in the instrument clus-
ter display. You may switch to perpendicular parking if
you desire. Push the OK button on the left side steering
wheel switch to change your parking space setting.

348

STARTING AND OPERATING

«
...
348
349
350
351
352
...
»

Содержание Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Pacifica Hybrid 2018

Бренд: GMC Страницы: 140

Бренд: Alfa Romeo Страницы: 8

Бренд: B-Speech Страницы: 4

Бренд: AddSecure Страницы: 14

Бренд: Paser Страницы: 2

Бренд: Xblitz Страницы: 56

Бренд: Lantronix Страницы: 51

Бренд: Rugged Ridge Страницы: 2

Бренд: Honda Страницы: 22

Бренд: Mercedes-Benz Страницы: 494

Бренд: Mazda Страницы: 1001

1500 CLASSIC 2020

Бренд: RAM Страницы: 360

Бренд: Subaru Страницы: 16

Turbocharger 15012

Бренд: Edelbrock Страницы: 1

Yukon XL Denali 2015

Бренд: GMC Страницы: 439

Бренд: Mitsubishi Страницы: 284

1997 Park Avenue

Бренд: Buick Страницы: 420

Giulia 952 2017

Бренд: Alfa Romeo Страницы: 324

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды