manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 82 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 82

Symptom:

P0123-THROTTLE POSITION SENSOR #1 HIGH

When Monitored and Set Condition:

P0123-THROTTLE POSITION SENSOR #1 HIGH

When Monitored:

With the ignition on. Battery voltage greater than 10 volts.

Set Condition:

Throttle Position Sensor voltage at the PCM is greater than 4.47 volts.

One Trip Fault.

POSSIBLE CAUSES

THROTTLE POSITION SENSOR SWEEP

INTERMITTENT CONDITION

(K22) TP SIGNAL CIRCUIT SHORTED TO (K6) 5 VOLT SUPPLY CIRCUIT

(K22) TP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

TP SENSOR INTERNAL FAILURE

(K22) TP SIGNAL CIRCUIT OPEN

(K4) SENSOR GROUND CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the throttle is fully closed and free from binding or carbon
build up.
Start the engine.
With the DRBIII

t

, read the TP Sensor voltage.

Is the voltage above 4.5 volts?

All

Yes

→

Go To

2

No

→

Go To

8

2

Turn the ignition off.
Disconnect the TP Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between the (K22) TP Signal circuit and the (K6) 5 Volt
Supply circuit in the TP Sensor harness connector.
Is the resistance below 100 ohms?

All

Yes

→

Repair the short to the (K6) 5 Volt Supply circuit in the (K22) TP
Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

76

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов