Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 84

TEST

ACTION

APPLICABILITY

7

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

8

Ignition on, engine not running.
With the DRBIII

t

, monitor the TP Sensor voltage.

Slowly open the throttle from the idle position to the wide open throttle position.
Does voltage start at approximately 0.7 of a volt and go above 3.5 volts with a smooth
transition?

All

Yes

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

78

DRIVEABILITY - NGC

P0123-THROTTLE POSITION SENSOR #1 HIGH —

Continued

«
...
82
83
84
85
86
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов