manualshive.com logo in svg

Chrysler Directed, Руководство по установке

Поделиться
Скачать
Chrysler Directed Скачать руководство пользователя страница 8

8

Directed Digital Solutions CHRYSLER13

© 2016-07-12 Directed. All rights reserved.

Installation (wiring diagrams & vehicle wiring reference charts)

Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 9 for important information on this installation.

86

85

30

87a

87

12: 

Brown

: (-) Lock Output

3: 

Brown/Red

: (+) 12V

4: 

Yellow/Red

: (+) Accessory Output

6: 

Yellow

: (-) Lock Input

9: 

Black

: (-) Ground

10: 

Red

: (+) 12V

Green 60-pin connector

(at BCM, dash fusebox)

Black 10-pin connector

(at Headlight Switch)

Gray 2-pin

connector

(at BCM,

dash fusebox)

HS CAN Low: 

Tan

: 4

HS CAN High: 

Tan/Black

: 5

MS CAN High: 

Orange/Green

: 7

MS CAN Low: 

Orange/Brown

: 8

(+) Ignition Output: 

White/Red

: 12

(-) Parking Lights Output: 

Lt. Blue/Black

: 13

(+) Starter Output: 

Green/Red

: 14

(-) Unlock Output: 

Dk. Blue

: 7

Siren

The Remote Start 
Safety Override 
Switch 

MUST 

be in 

the ON position.

Remote Start Safety

Override Switch

Hood Pin

(-) Hood Input: 

Gray

: 3

(+) Siren Output: 

Brown

: 17

B

A

1

2 3 4 5

6 7 8 9 10

1

16

31

46

15

30

45

60

(+) Accessory: 

Gray,

 pin 1

(+) Ignition:

Blue,

 pin 2

(MUX) Parking Lights:

White/Orange,

 pin 1

Black 2-pin connector

(at Ignition Switch)

1 2

Black 3-pin connector

(at Ignition Switch)

1

2

(+) Starter:

Brown

, pin 3

(MUX) Door Locks:

White/Blue

, pin 14

3

OBDII 
Diagnostic
Connector

C-CAN Low: 

Brown

, pin 14

C-CAN High:

Lt. Green

, pin 6

B-CAN Low: 

White

, pin 11

B-CAN High:

Blue

, pin 3

16

8

9

1

(+) 12V: 

Red

, pin A

Resistor

2.5 k

Ω

Resistor

370 

Ω

CUT

Resistor

500 

Ω

Fuse 5A

Содержание Directed



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды