Chrysler 2012 Ram Truck Gas 1500 Скачать руководство пользователя страница 565 | Manualshive

Страница: 565 / 720

background image

2. The total GVWR or the Front GAWR or the Rear
GAWR should never be exceeded.

3. Cargo capacity will be reduced by the addition of
options or passengers, etc.

The loaded vehicle weight, including the snowplow sys-
tem, all aftermarket accessories, driver, passengers, op-
tions, and cargo, must not exceed either the Gross Vehicle
Weight (GVWR) or Gross Axle Weight (GAWR) ratings.
These weights are specified on the Safety Compliance
Certification Label on the driver’s side door opening.

NOTE:

Detach the snowplow when transporting pas-

sengers.

Vehicle front end wheel alignment was set to specifica-
tions at the factory without consideration for the weight
of the plow. Front end toe-in should be checked and reset
if necessary at the beginning and end of the snowplow
season. This will help prevent uneven tire wear.

The blade should be lowered whenever the vehicle is
parked.

Maintain and operate your vehicle and snowplow equip-
ment following the recommendations provided by the
specific snowplow manufacturer.

Over The Road Operation With Snowplow
Attached

The blade restricts air flow to the radiator and causes the
engine to operate at higher than normal temperatures.
Therefore, when transporting the plow, angle the blade
completely and position it as low as road or surface
conditions permit. Do not exceed 40 mph (64 km/h). The
operator should always maintain a safe stopping distance
and allow adequate passing clearance.

Operating Tips

Under ideal snow plowing conditions, 20 mph (32 km/h)
should be maximum operating speed. The operator
should be familiar with the area and surface to be

5

STARTING AND OPERATING

563

«
...
563
564
565
566
567
...
»

Содержание 2012 Ram Truck Gas 1500

















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2012 Ram Truck Gas 1500

Бренд: kaarta Страницы: 29

Бренд: Toyota Страницы: 35

Бренд: Victory 4x4 Страницы: 13

Бренд: Subaru Страницы: 21

Бренд: Jeep Страницы: 1528

Бренд: TAUBENREUTHER Страницы: 8

Бренд: Meta System Страницы: 16

Бренд: VER-MAC Страницы: 64

2013 GMC Savana

Бренд: GMC Страницы: 398

Бренд: Calix group Страницы: 4

Бренд: Mitsubishi Страницы: 362

Escalade 2004 Escalade ESV

Бренд: Cadillac Страницы: 472

CHALLENGER GK-6125A 2018

Бренд: Coolster Страницы: 45

1953 Traction Avant

Бренд: CITROEN Страницы: 26

Бренд: Suzuki Страницы: 504

Бренд: Mazda Страницы: 14

Бренд: Curt Manufacturing Страницы: 4

Бренд: Metra Electronics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды