Chrysler 2012 Ram Truck Gas 1500 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 720

background image

•

Remote Start Aborted — Hood Ajar

•

Remote Start Aborted — Fuel Low

•

Remote Start Aborted — System Fault

•

Remote Start Disabled — Start Vehicle to Reset

The EVIC message stays active until the ignition is turned
to the ON/RUN position.

To Enter Remote Start Mode

Press and release the REMOTE START button
on the RKE transmitter twice within five sec-
onds. The parking lights will flash and the horn
will chirp twice (if programmed). Once the

vehicle has started, the engine will run for 15 minutes.

NOTE:

•

If your power door locks were unlocked, Remote Start
will automatically lock the doors.

•

If an engine fault is present or fuel level is low, the
vehicle will start and then shut down in 10 seconds.

•

The park lamps will turn on and remain on during
Remote Start mode.

•

For security, power window and power sunroof op-
eration (if equipped) are disabled when the vehicle is
in the Remote Start mode.

•

The engine can be started two consecutive times (two
15-minute cycles) with the RKE transmitter. However,
the ignition switch must be cycled to the ON/RUN
position before you can repeat the start sequence for a
third cycle.

To Exit Remote Start Mode Without Driving The
Vehicle

Press and release the REMOTE START button one time or
allow the engine to run for the entire 15-minute cycle.

28

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
28
29
30
31
32
...
»

Содержание 2012 Ram Truck Gas 1500

















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2012 Ram Truck Gas 1500

Бренд: Baja Designs Страницы: 6

Multiple G9F18 AU000

Бренд: Genesis Страницы: 3

Prestige APS-45B

Бренд: Audiovox Страницы: 8

Бренд: Volvo Страницы: 138

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

Бренд: Subaru Страницы: 34

Бренд: EUFAB Страницы: 12

Intercooler Kit Type 31

Бренд: GReddy Страницы: 9

Бренд: Yakima Страницы: 11

RUDDER ANGLE INDICATOR

Бренд: VDO Страницы: 8

Бренд: Chevrolet Страницы: 372

ADARAC Aluminum M Series

Бренд: aci Страницы: 16

Бренд: Imiola HAK-POL Страницы: 3

Dunlop L.D02.C.M

Бренд: Sumitomo Страницы: 22

Бренд: Toyota Страницы: 600

Бренд: Fabbri Страницы: 32

Бренд: Whelen Engineering Company Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды