manualshive.com logo in svg

Chroma 19032-P, Быстрый старт

Поделиться
Скачать
Chroma 19032-P Скачать руководство пользователя страница 12

side wires.    If so, it could cause the product or PC to be 
down or damaged.   
 

 

 

 
 

Storage, Freight, Maintenance & Cleaning 

 

Storage 

When don’t use the device, please pack it properly and store under a good 
environment.    (The packing is no needed when the device under 
appropriate environment.)   
 

Freight 

Please use the original packing material when move the device.    If the 
packing material is missing, please use the equivalent buffer material to 
pack and mark it fragile and waterproof etc to avoid the device damage 
during movement.    The device belongs to precise equipment, please 
use-qualified transportation as possible.    And avoid heavy hitting etc to 
damage the device. 
 

Maintenance 

The device is without any maintenance operation for the general user.   
(Except for the notice in the manual.)    Please contact our company or 
agent when the device occurred the user judgment abnormal.    Don’t 
maintain by yourself to avoid occurred unnecessary danger and serious 
damage to the device.     
 

Cleaning 

Remove all connected wires and cables on the instrument before cleaning.   
Use a brush gently to clean the dust on it.    For internal cleaning, use a 
low-pressure air gun to vacuum the dust inside or send it back to the 
distributors or agents of Chroma for cleaning. 
 

x 

 

Содержание 19032-P
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды