Christie VeinViewer Flex Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 76

background image

50

CHAPTER TEN: TROUBLESHOOTING

020-300020-03 Rev. 1 (03-2013)

VEINVIEWER FLEX USER GUIDE

Unable to establish USB
connection to VeinViewer
Flex

None

VeinViewer device drivers were
not properly installed

Make sure Flex Connect software is running and that VeinViewer is connected to
a power source, but NOT turned ON.

WINDOWS 7

Disconnect and re-connect VeinViewer to the PC via USB connection. The
"Installing device driver software" pop-up should come up on the windows
status bar. The device driver should automatically install.

On the "VeinViewer -Connect" prompt, select "Refresh" button. The
VeinViewer should be listed on the "Device(s):" pull down menu as "\\.\COM#.
Select "Connect", the Device Control panel on the Flex Connect software
should now be active. If VeinViewer was not listed in the pull down menu,
proceed to step below.

From the windows start menu, select the "Install VeinViewer Flex Drivers"
located in the "Christie" folder.

Click "Next" in the "Device driver installation wizard" prompt.

Select the checkbox for "Always trust software from Christie Medical Holdings”,
and then select "Install" in the windows security prompt. A notification should
appear that drivers were successfully installed.

Select "Refresh" in the "VeinViewer-Connect" prompt. The VeinViewer should
be listed on the "Device(s):" pull down menu as "\\.\COM#. Select "Connect",
the Device Control panel on the Flex Connect software should now be active.

PROBLEM

STATUS INDICATOR

CAUSE

SOLUTION

«
...
54
55
56
57
58
...
»

Содержание VeinViewer Flex













































































Отзывы:

Нет отзывов

Похожие инструкции для VeinViewer Flex

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: ParaBody Страницы: 5

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: Bowa Страницы: 140

Бренд: Toparc Страницы: 32

Wensco AnPro180 Stick

Бренд: G2G Lighting Страницы: 3

Бренд: GreenDS Страницы: 24

Бренд: Ryobi Страницы: 168

Бренд: XD COLLECTION Страницы: 28

Бренд: Tascam Страницы: 32

Бренд: Raymarine Страницы: 3

Бренд: Obdstar Страницы: 16

Бренд: Foxwell Страницы: 64

Бренд: 2connect Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды