Chongqing Xiegu Technology X5105 Скачать руководство пользователя страница 49

Страница: 49 / 56

Operation

Configuration parameter list

After updating the firmware, be sure to configure X5105 as described in this document, otherwise the device will not work properly!



After the firmware is updated, go directly to item 21 of the system menu

【

Reset ALL

】

and reset the system parameters.



After the reset is complete , consult the appropriate configuration parameters in accordance with the serial number of the serial number of the host .

Configuration one:

Application range: X0300001

～

X0300150 / 0300001

～

0300220

Menu Item

Function Description

Recommended setting

Tx AF Gain SSB

MIC gain in SSB mode

60%

Misc Option

Digital baseband configuration

0x7A5C3360

Ext MIC Bias

External MIC offset setting

Enable

Configuration two:

Application range: X0300151 and its follow-up / 0300221and its follow-up

Menu Item

Function Description

Recommended setting

Tx AF Gain SSB

MIC gain in SSB mode

80%

Misc Option

Digital baseband configuration

0x59A03360

Ext MIC Bias

External MIC offset setting

Enable

After setting up, click

SAVE

to save, exit system menu. Execute a boot and shutdown immediately.

When you first use it, check if the

SQL

、

NTH

project is set up. If the settings are in place, please clear them all manually. And press all

button .

When using a preset message for the first time, please manually delete all scrambled symbols in

RE1

～

RE3

Содержание X5105

























































Результаты поиска

Содержание X5105

Отзывы:

Chongqing Xiegu Technology X5105, Инструкция по эксплуатации, Страница: 49 / 56

Результаты поиска

Содержание X5105

Отзывы: