background image

03

No.

1

2

3

4

Motion time

No motion within 2h

Motion within 2h

Motion within 2min

2s

Tp

10s

Table 4 Auxiliary Circuit Technical Parameters

Product model

NJBK6-36/3, NJBK6-36/9, 

NJBK6-36/24, NJBK6-36/36

1

2

3

4

5

6

Rated insulation voltage (V)

Rated impulse withstand voltage Uimp (kV)

Agreed free air heating current Ith (A)

Rated operating voltage Ue(V)

No.

380

2.5

5

240V

380V

AC-15

1.5

0.95

Use type under rated operating voltage and 
rated operating current Ie(A)

SCPD model

6A Gg

2.1

 Motion characteristic

2.1.1 See Table 5 for the motion characteristic of overload protection

Table 5 Motion Characteristic of Overload Protection

Setting current 

multiple

1.05

1.2

1.5

7.2

Cold

Thermal

Cold

Starting 

condition

Ambient air 

temperature (℃)

+

20

2.1.2  Motion  characteristic  of  phase  loss  protection:  When  any  one  of  the 
three-phase currents of the main circuit is open, the protector motions for 
3s, with a relative error of ± 20%.

2.1.3  Motion  characteristic  of  three-phase  unbalance  protection:  When  the 
three-phase  current  of  the  main  circuit  conforms  to  the  following  formula, 
the protector motions for 3s with a relative error of ± 20%.

30%

100%

|

|

i

3

1

i

>

×

-

=

avg

avg

I

I

I

Max

Where: 

Содержание NJBK6 Series












Отзывы: