CCH01788:08/00
4
To relocate Crib Spring, Remove
Hexhead Machine Screws
B
B
B
B
B
then move Tabs to desired height.
Locate Tabs on Spring
R
and rotate Tabs upward. Position the four
Tabs on Spring
R
to the desired height allowed by the threaded holes
located on the 4-Position Spring Brackets
G
. Install a Hexhead Machine
Screw
B
through each Spring Tab and into the selected threaded re-
ceiving hole on Spring Bracket
G
. Tighten Screws
B
with a 3/8
(10mm) wrench. Follow the same procedure when changing spring
heights at a later date. Periodically check Hexhead Machine Screws
B
and tighten if needed.
S
TEP
5 - D
IAGRAM
4: S
PRING
I
NSTALLATION
Holes to
receive
Phillips
Head
Machine
Screws
F
for
attachment
to ends
P
&
Q
.
D
IRECTIONS
FOR
C
ONVERTING
C
RIB
TO
A
T
ODDLER
B
ED
When use as a crib has been completed, you have the option to convert to
a Toddler Bed for years of additional use in your childs room. Refer to
Step
4 - Diagram 3.
Remove Front Side
M
and Foot Top Dowel
T
. Install Crib
Stretcher
S
as shown in
Sketch A
. Dowel on Stretcher
S
locates in top
hole at bottom of Foot Post
P
&
Q
, then secure with K-D Bolt
E
and K-
D Bolt Plug
C
shown installed. Install Insert Nut
J
and Allenhead Bolt
I
in
holes near top of Foot Post
P
&
Q
as shown. Tighten Allenhead Bolt
I
with Allen Wrench
A
and Insert Nut
J
with Allen Wrench
H
.
Spring
R
R
R
R
R
must be installed in lowest position.
Store the removed parts and
hardware in the event you wish to convert your Toddler Bed back to a crib.
Sketch A
(style may vary)
F
MAINTENANCE OF YOUR CHILD CRAFT CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD:
Upon completion of assembly be sure all
screws, bolts and fastening devices have been tightened securely. A frequent check should be made of all screws, bolts and fastening devices and
tightened if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT
use crib
if parts are missing or broken. Contact your Dealer or Child Craft (812) 883-3111, for a replacement part or instructional literature if needed. Include Model
Identification Number with your request which you recorded on page 2 of these instructions.
DO NOT SUBSTITUTE PARTS. DO NOT MAKE ANY
ALTERATIONS NOT DESCRIBED IN THESE ASSEMBLY DIRECTIONS.
F
CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD:
Mix together a mild solution
of gentle dishwashing liquid and water, apply to surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a
soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth.
NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
F
STORAGE AND USE OF YOUR CHILD CRAFT CRIB/TODDLER BED/FULL SIZE HEADBOARD & FOOTBOARD:
A printed plastic pouch is attached to
the crib spring for the permanent storage of the assembly directions. After completing the assembly process you are advised to read and be aware of
all
WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE
notices contained in this set of directions and printed on the plastic pouch
located on the underneath side of the crib spring. You will then place the complete set of assembly directions into the plastic pouch for future referral
by opening storage drawer. We caution you not to place excess hadrware in the plastic pouch as it could present danger to a child if retrieved. When
storing crib use
CAUTION
as extreme temperature or humidity changes could be harmful. Use
CAUTION
when a vaporizer is in use, always aim vapor
stream away from crib as well as away from any wood furniture item.
D
IRECTIONS
FOR
C
ONVERSION
TO
A
F
ULL
S
IZE
H
EADBOARD
& F
OOTBOARD
Disassemble crib by removing Spring
R
, Headboard
N
and Footboard
O
from Foot Posts
P
&
Q
, and Station-
Sketch B
(style may vary)
Spring
R
must be installed
in lowest position.
ary Side
L
. You have the option to remove the 4-Position Spring Brackets
G
from the
Footboard Posts
P
&
Q
if you desire, but
do not remove the factory installed brackets
G
G
G
G
G
on the Stationary Side
L
L
L
L
L
or any other items attached with wood screws
.
Attach
the Stationary Side and the Footboard Assembly to a Hook-End style full size bed frame
(model 6444) at the desired height. The Hooks on the bed frame locate over the factory
installed pins located in the slots in the Headboard and Footboard Assembly. Insert the Hole
Button Covers
K
as shown.
NOTE: When using as a Toddler Bed the
mattress must have minimum dimensions
of 51-5/8 in. (1310mm) in length and 27-1/4
in. (690mm) in width and 4 in. (100mm) in
thickness but not to excees 6 in.
It is very important that the Stretcher
S
S
S
S
S
is used when converting to a Toddler Bed.
Failure to install this part could result in
serious injury or death.
When using as a Toddler bed, the mini-
mum age shall not be less than 15 months
and the maximum weight shall not be
greater than 50 lb (22.7 kg).
WARNING
4-Position
holes to
receive
Hexhead
Machine
Screws
B
to be
placed in
selected
height
position
hole for
Spring
R
positioning
Tab
Top surface
R
CLOSE UP VIEW
Tab
B
G
G
I
J
I
S
E
K
s
K
L
P
T
Q
M
!
