background image

MF1, MF2, PF1, PF2 Series

Installation Instructions

10

Using the Stand

CAUTION:

This stand is intended for use only with the

products and maximum weights indicated: 125 lbs (56.70 kg)
for the MF1, 250 lbs (113.40 kg) for the MF2 [125 lbs
(56.70 kg) per faceplate]; 200 lbs (90.72 kg) for the PF1,
400 lbs (181.44 kg) for the PF2 [200 lbs (90.72 kg) per
faceplate]. Use with other products or products heavier than
the maximum weights indicated may result in instability
causing possible injury.

WARNING:

STAND CAN TIP OVER RESULTING IN RISK

OF INJURY. Never move the stand when displays are
attached. Never push against the stand.

Removing Display(s) from Stand

1.

Remove bolt or padlock from faceplate (if used).

NOTE:

The pin may have been used as a more permanent

locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.

2.

Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 15)

WARNING:

EACH DISPLAY MAY WEIGH IN EXCESS OF

40 LBS! Always use two people and proper lifting techniques
when installing or positioning display on stand.

3.

Carefully lift display(s) from stand.

4.

Lift up on pin and place flag back against faceplate to return
it to "Closed" position.

Figure 15

2

1

Remove bolt
or padlock
if used

Pin in
"Open"
position -

Pin in
"Closed"
position -

4

move to
"Open"
position to

move to
"Closed"
position

remove
display

after display
is removed.

Содержание MF1 Series













Отзывы: