background image

Installation Instructions

 JSBV

5

INSTALLATION

WARNING:  

IMPROPER INSTALLATION CAN LEAD TO 

MOUNT FALLING CAUSING SERIOUS PERSONAL 
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute 
hardware. Only use hardware provided or specified by 
manufacturer.

1.

Place JSBV interface bracket over the mounting holes on 
the back of the display, making sure to center the bracket as 
much as possible.

WARNING:  

IMPROPER INSTALLATION CAN LEAD TO 

DAMAGE TO EQUIPMENT OR TO MOUNT FALLING 
CAUSING SERIOUS PERSONAL INJURY ! Use proper size 
and length hardware depending on display.

NOTE:  

Use spacers from hardware bag C if the display 

mounting holes are recessed, or if there is some 
protrusion or bowing in the back of display.

NOTE:  

Use screws from hardware bags A, B, or E, dependent 
upon whether or not spacers are required.

2.

Using the same number of spacers (if required) and screws 
as holes in the display back, attach JSBV interface bracket 
to the display back. (See Figure 1)

Figure 1

CAUTION:  

PREVENT EQUIPMENT DAMAMGE! Tighten 

each screw carefully, but do NOT overtighten.

Attach Interface Bracket to Display

1.

Lay display face down on a clean and dry flat surface.

2.

Attach Interface Bracket (A) to display using appropriate 
screws (C-H, N-Q). (See Figure 2)

NOTE:  

If  the display has a recessed mounting surface, 

spacers (K or J) between the display and Interface 
Bracket (A) may be required.

3.

Tighten all screws.

Figure 2

Attach Display to Mount

1.

Start two M4 x 8mm Phillips pan head screws (B) into top 
mounting holes on interface bracket (A). (See Figure 3)

2.

Align two screws in interface bracket (A) with upper 
mounting holes in Centris cup and lower display until 
screws are seated in lower area of teardrop mounting  
holes. (See Figure 3)

Figure 3

3.

Hold display so that display back is against Centris cup and 
install two M4 x 8mm Phillips pan head machine screws (B) 

 

   (J) or (K) if needed
[from hardware bag C]

(A)

(D through H,
N through Q)

2

2

(A)

(C-H, N-Q)

(B) x 4

2

(A)

Содержание J Series









Отзывы: