Chicco Sirio 012, Инструкция по эксплуатации

Страница: 26 / 224

26
not be guaranteed otherwise.
• This child car seat is only approved for use
for children that weight between 0 and 25
kg (from birth up to 6 years of age, approx-
imately).
• The vehicle’s seat must be equipped with
3-point seat belt, static or retractable, that
complies with UNI/ECE Regulation no. 16 or
other equivalent standards (Fig. 4).
•
WARNING!
Never fit the child car seat to a
seat that is only equipped with a 2-point seat
belt (Fig. 5).
• The child car seat can be fitted on the front
passenger seat or any of the back seats. Nev-
er use this child car seat on side-facing or
rear-facing car seats (Fig. 6).
• This product is expressly intended to be used
only as a child car seat; it should not be used
indoors.
4. HOW TO FIT THE GROUP 0+ (FROM 0 UP
TO 13 kg) CHILD CAR SEAT IN THE CAR
A
IRBAG
WARNING!
When it is used for Group 0+
(from 0 up to 13 kg), always fit the child car
seat in a rearward-facing direction. If the front
seat of the car is equipped with an airbag, de-
activate the airbag before fitting the child car
seat. Death or serious injury hazard.
WARNING!
The points through which the
seat belt must pass for fitting the Group 0+
seat (from 0 up to 13 kg) are highlighted in
LIGHT BLUE.
WARNING!
Never use the booster cushion if
the child weighs over 9 kg.
Adjust the child car seat to position 4, the
maximum angle of inclination, using the incli-
nation adjustment lever (G), (Fig. 7).
Position the child car seat so that it faces the
rear of the car and extract the car’s 3-point
seat belt, pulling it out as fare as possible.
Pass the abdominal and diagonal sections be-
tween the seat and the base of the child car
seat (Fig. 8).
Fasten the buckle of the seat until you hear a
“CLICK” (Fig. 9).
Begin assembly on the same side as the buck-
le. Take the diagonal portion of the belt and
insert completely in the red clamp (L), holding
it open (Fig. 10). Then insert the belt in the
specific light blue belt guide (N) (fig. 11).
Continue to assemble on the side of the re-
tractable part of the belt. Completely insert
the belt in the red clamp (L), holding it open
(Fig. 12). Then insert the belt in the specific
light blue belt guide (N) (Fig. 13).
To make the belt as tight as possible, pull the
diagonal portion towards the retractor hold-
ing open the clamp (L) on the opposite side
(that of the buckle) so the belt can slide cor-
rectly (Fig. 14).
WARNING!
Check that the child car seat is fit-
ted firmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely fitted
into the car seat, repeat the installation.
WARNING!
Always check that the seat belt
is distributed evenly at all points and that it is
not twisted.
WARNING!
NEVER fit the car seat belt in any
way not mentioned in these instructions.
WARNING!
In case of use in vehicles equip-
ped with rear seat belts with integrated ai-
rbags (inflatable belts), the interaction of the
inflatable portion of the vehicle’s belt with this
child restraint can result in serious injury or de-
ath! Do not install this child restraint using an
inflatable seat belt.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
5. HOW TO FIT THE GROUP 1 (9-18 kg)
CHILD CAR SEAT TO THE CAR WITH THE
ISOFIX SYSTEM
WARNING!
If the child weighs less than 9 kg
do not use a front-facing car seat.
To fit the car seat, remove the Isofix connec-
tors (P) by pulling belt (R) towards the exterior
(Fig. 15).