background image

4)

 

Use 

SCROLL

 button to view the status of the MIL light (

“ON” or 

“OFF

) and the following monitors: 

z

 

Misfire monitor

 -- Misfire monitor 

z

 

Fuel System Mon -- 

Fuel System Monitor 

z

 

Comp. Component 

-- Comprehensive Components Monitor 

z

 

EGR 

-

- EGR System Monitor 

z

 

Oxygen Sens Mon 

-- O2 Sensors Monitor 

z

 

Catalyst Mon 

--

 Catalyst Monitor 

z

 

EVAP System Mon 

-- Evaporative System Monitor 

z

 

Oxygen Sens htr 

--O2 Sensor Heater Monitor 

z

 

Sec Air System 

-- Secondary Air Monitor 

z

 

Htd Catalyst

 -- 

Heated Catalyst Monitor 

z

 

A/C Refrig Mon 

-- A/C system Monitor                                     

………..

Since DTCs Cleared

…………..

 

                                                              1/3 
MIL Status                                  OFF       

Misfire Monitor                          OK 
Fuel System Mon.                    OK 
Comp. Component                  OK 

 

           

                                               

 

 

5)

 

If the vehicle supports readiness test of “

This Drive Cycle

”, a 

screen of the following will be displayed: 

………….

This Drive Cycle

…………  …. 

                                                1/3 

MIL Status                                ON           
Misfire Monitor                        OK 
Fuel System Mon                    OK 
Comp. Component                OK 

 

       

                                                     

z

 

The number “x/x” to the upper right corner of the screen 
indicates total number of screens the retrieved data cover 
and sequence of currently displayed data. 

6)

 

Press

 ENTER/EXIT

 button to return to previous menu.

 

 

 

21

Содержание 98568



























Отзывы: