manualshive.com logo in svg

Chicago Pneumatic CPG 90-120 JD, Инструкция по эксплуатации

Поделиться
Скачать
Chicago Pneumatic CPG 90-120 JD Скачать руководство пользователя страница 15

- 15 -

Qc1002™ Module

The Qc1002™ module is located inside the control
panel. This control module will carry out all
necessary tasks to control and protect a generator,
regardless of the use of the generator.

This means that the Qc1002™ module can be used for
several applications.

Pushbutton and LED functions

Following pushbuttons are used on 
the Qc1002™

Following LEDs are used on the 
Qc1002™

ENTER:

 Is used to select and 

confirm changed settings in the 
Parameter list.

UP: 

Is used to scroll through the 

display information and to adjust 
parameter value upwards.

DOWN:

 Is used to scroll through the 

display information and to adjust 
parameter value downwards.

BACK: 

Is used to leave the Alarm 

pop-up window, to leave the 
Parameter list and to leave menu's 
without change.

REMOTE MODE: 

Is used to 

activate the remote mode. The LED 
indicates if the gen-set is put in 
Remote Mode.

START:

 Is used to start the unit in 

Manual Mode.

STOP:

 Is used to stop the unit in 

Manual or Remote Mode (without 
cooldown). When the unit is stopped 
with the STOP button in Remote 
mode, it will automatically go to 
Manual Mode.

Power

Green LED indicates that the unit is 
powered up.

Remote

Green LED indicates that the Remote 
Mode is selected.

Start/Stop

Green LED indicates that the engine is 
running.

Alarm

Flashing red LED indicates that an 
alarm is present. A continuous red 
LED indicates that the alarm has been 
acknowledged by the user. The exact 
alarm is shown on the display.

Содержание CPG 90-120 JD

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды