Chicago Electric 94280 Скачать руководство пользователя страница 5

Page 5

SKU 94280

For technical questions, please call 1-800-444-3353.

Avoid electrical shock.  

Make sure the Floor Machine is unplugged 

from its electrical outlet prior to performing any inspection, maintenance, 
or cleaning procedures.  Do not use the Floor Machine in the rain or in 
wet conditions.  Plug the Power Cord of this unit only into a 3-hole, 115 
volt, Ground Fault Circuit Interrupter (GFCI), electrical outlet for addi-

tional protection from electric shock.

Use the right product for the job.  

There are certain applications for which this 

product was designed.  Do not use small tools, equipment, or accessories to do the 
work of larger industrial tools, equipment, or accessories.  Do not use this product 
for a purpose for which it was not intended.

Do not allow children or other unauthorized people to handle or play with 
this product.

Industrial applications must follow OSHA requirements.

To reduce the risk of fire, use only commercially available floor cleaners and 
waxes.

WARNING!  

People with pacemakers should consult their physician(s) before 

using this product.  Electromagnetic fields in close proximity to a heart pacemaker 
could cause interference to or failure of the pacemaker.  In addition, people with 
pacemakers should adhere to the following:  Avoid operating power tools alone.  
Don’t use a power tool with the Power Switch locked on.  If powered via a Power 
Cord be certain that the tool is properly grounded.  A ground fault interrupt (GFCI) 
system is also a good precaution.  This inexpensive device is a good safety measure 
because it prevents a sustained electrical shock.  Properly maintain and inspect all 
tools before use to avoid electrical shock.

WARNING!  

The warnings and cautions discussed in this manual cannot cover 

all possible conditions and situations that may occur.  It must be understood by the 
operator that common sense and caution are factors which cannot be built into this 
product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

6.

.

8.

9.

10.

11.

12.

Содержание 94280
















Отзывы: