background image

15.        WARNING!   People with pacemakers should consult their physician(s) before

using this product.  Electromagnetic fields in close proximity to a heart pacemaker could
cause interference or failure of the pacemaker.  In addition, people with pacemakers
should adhere to the following:  Avoid operating power tools alone.  Don’t use a power
tool with the power switch (Trigger) locked on.  If powered via a power cord be certain
that the tool is properly grounded.  A ground fault interrupt (GFCI) system is also a good
precaution.  This inexpensive device is a good safety measure because it prevents a
sustained electrical shock.  Properly maintain and inspect all tools before use to avoid
electrical shock.

16.           WARNING!   The warnings, precautions, and instructions discussed in this manual

cannot cover all possible conditions and situations that may occur.  The operator must
understand that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.

14.

   WARNING!    Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known (to the State of California) to cause
cancer, birth defects or other reproductive harm.  Some examples of these chemicals
are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry
products, arsenic and chromium from chemically treated lumber.  Your risk from these
exposures varies, depending on how often you do this type of work.  To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.  

(California Health & Safety Code 25249.5, et seq.)

13.Always switch to a fresh Battery (40) when tool performance begins to diminish.

Severe heat is most destructive to a Battery.  The more heat generated, the faster the
Battery loses power.  A Battery that gets too hot can be permanently damaged.  Never
over-discharge a Battery by using the tool while tool performance is decreasing.  Never
attempt to discharge a tool’s Battery by continuing to pull the tool Trigger (34).  When tool
performance begins to diminish, stop the tool, recharge the Battery, and use the fresh
Battery for optimal performance.

SKU 92472         For technical questions, please call 1-800-444-3353         PAGE 6

PRODUCT FEATURES

NOTE: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 11.

1.          WARNING!   Always make sure the Trigger (34) of the Impact Driver is in its “OFF

Содержание 92472












Отзывы: