Chicago Electric 91757 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 18

Chicago Electric 91757 Скачать руководство пользователя страница 15

SKU 91757 For technical questions please call 1-800-444-3353 PAGE 15

To Operate The Laser Guide:

1.

To activate the Laser Guide (86) depress the Laser Button (34). Align the Laser
Beam with the marked cut line. Then, turn on the Circular Saw and make the cut.
NOTE: Turn on the Laser

only when you are ready to start cutting, and make

sure the Laser if off when not cutting. (See Figure J.)

To Adjust The Laser Beam:

1.

The Laser Beam is pre-set by the manufacturer. However, should it become
necessary to adjust the Laser Beam, remove the two Screws (45, 46) located on
the side of the Laser Guide (86). Then remove the Side Cover on the Laser
Guide. (See Assy. Diagram.)

2.

Inside the Laser Guide (86) are two Screws (48). Adjust

only one Screw at a

time and

gently move the Laser Base Body to make the adjustment. Then re-

tighten the Screw. Repeat this process with the remaining Screw until the Laser
Beam is correctly adjusted. (See Assy. Diagram.)

3.

To check the Laser Beam alignment, place the sides of the Saw Teeth against a
straight edge, and adjust the Laser Beam to follow the straight edge. Always
adjust and check both the 90 and 45 degree angles. (See Assy. Diagram.)

4.

Once the Laser Beam is adjusted replace the Side Cover and two Screws
(45, 46). (See Assy. Diagram.)

LASER BUTTON (34)

LASER GUIDE (86)

FIGURE J

«
...
13
14
15
16
17
...
»

Содержание 91757



















Отзывы:

Нет отзывов