background image

Page 6

For technical questions, please call 1-888-866-5797.

Item 62427 

        

SAFET

y

Op
ERA
TION

M

AINTENANCE

SETU
p

Grounding

TO pREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING: 

Check with a qualified electrician if you are in doubt as to whether the outlet is properly 

grounded.  Do not modify the power cord plug provided with the charger.  Do not use the charger 

if the power cord or plug is damaged.  If damaged, have it repaired by a service facility before 

use.  If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

Extension Cords

Note:

  Extension cords must not be used with this item’s Charger.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~

Volts Alternating Current

A

Amperes

n0 xxxx/min.

No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk 

of Eye Injury.  Wear ANSI-approved 

safety goggles with side shields.

Read the manual before 

set-up and/or use.

WARNING marking concerning 

Risk of Hearing Loss.  

Wear hearing protection.
WARNING marking 

concerning Risk of Fire.  

Do not cover Charger 

ventilation ducts.

Charge on fireproof surface only.

WARNING marking concerning 

Risk of Electric Shock.  

Properly connect Charger’s power 

cord to appropriate outlet.

WARNING marking concerning 

Risk of Explosion.  

Do not puncture, short, or open 

battery packs and do not charge 

damaged battery packs.

Содержание 62421

















Отзывы: