Chicago Electric 61973 Скачать руководство пользователя страница 15

Страница: 15 / 20

Page 15

For technical questions, please call 1-888-866-5797.

Item 61973

Calibrating the Miter Table Indicator

After checking or adjusting the fence to
confirm that it is at 90º to the Blade, check the
accuracy of the Miter Table Angle Indicator.

1. Loosen the screw holding the

Angle Indicator in place.

2. Rotate it until the pointer is exactly on 90º.

3. Retighten the screw.

Calibrating the Bevel Angle

For making accurate cuts, the Saw Blade must
be adjusted to be exactly vertical to the Table.

1. To check the angle, have the blade assembly

in its normal upright position. Make a cut on a
piece of flat sided, fairly thick scrap material.

2. Check the cut with an accurate square.

The cut should be at exactly 90º.

3. Angle can also be checked by rotating one cut-off

piece 180º and holding the cut ends together.
If the cut is not exactly vertical,
the two pieces will form a slight angle.

4. If necessary, the bevel angle can be corrected

by adjusting the Bevel Adjustment Screw on
the right side under the Bevel Locking Lever.

5. Once the bevel angle is adjusted, adjust the Bevel

Angle Indicator to read 0º when the Saw Blade is
in the vertical position. Loosen the screw holding
the Indicator in place, adjust it to be exactly
over the 0º mark, then retighten the screw.

Adjusting or Replacing the Kerf Board

If the Kerf Board becomes damaged it must be replaced.

1. Remove the four screws holding

the Kerf Board in place.

2. Install a new Kerf Board. Replace the four

screws and tighten them slightly.

To adjust the Kerf Board:

1. Lower the Saw Blade and lock it

down with the Locking Pin.

2. Adjust the Kerf Board so the right side of the

Blade slightly clears the edge of the Kerf Board.

3. Loosen the Bevel Lock and set

the Bevel Angle at 45º left.

4. Ensure that the left side of the

Blade clears the Kerf Board.

5. Tighten the four screws holding

the Kerf Board in place.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Содержание 61973





















Результаты поиска

Содержание 61973

Отзывы:

Похожие инструкции для 61973

Бренды по названию

Популярные бренды

Chicago Electric 61973, Руководство пользователя

Результаты поиска

Содержание 61973

Отзывы:

Похожие инструкции для 61973

Бренды по названию

Популярные бренды