background image

Page 6

For technical questions, please call 1-888-866-5797.

Item 56776 

        

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM 
INCORRECT GROUNDING WIRE CONNECTION: 
Check with a qualified electrician if you are in doubt as to whether the outlet is properly 
grounded.  Do not modify the power cord plug provided with the tool.  Never remove the 

grounding prong from the plug.  Do not use the tool if the power cord or plug is damaged.  If damaged, have 
it repaired by a service facility before use.  If the plug will not fit the outlet, have a proper outlet installed by 
a qualified electrician.

Grounded Tools: Tools with Three Prong Plugs

 

3-Prong Plug and Outlet

1.  Tools marked with “Grounding Required” have 

a three wire cord and three prong grounding 
plug.  The plug must be connected to a properly 
grounded outlet.  If the tool should electrically 
malfunction or break down, grounding provides 
a low resistance path to carry electricity away 
from the user, reducing the risk of electric shock.  

(See 3-Prong Plug and Outlet.)

2.  The grounding prong in the plug is connected 

through the green wire inside the cord to the 
grounding system in the tool.  The green wire 
in the cord must be the only wire connected to 
the tool’s grounding system and must never 
be attached to an electrically “live” terminal.  

(See 3-Prong Plug and Outlet.)

3.  The tool must be plugged into an appropriate outlet, 

properly installed and grounded in accordance 
with all codes and ordinances.  The plug and outlet 
should look like those in the preceding illustration.   

(See 3-Prong Plug and Outlet.)

Extension Cords

1. 

Grounded

 tools require a three wire extension cord.  

Double Insulated

 tools can use either 

a two or three wire extension cord.

2.  As the distance from the supply outlet increases, 

you must use a heavier gauge extension cord.  
Using extension cords with inadequately sized wire 
causes a serious drop in voltage, resulting in loss of 
power and possible tool damage.  

(See Table A.)

3.  The smaller the gauge number of the wire, the 

greater the capacity of the cord.  For example, 
a 14 gauge cord can carry a higher current 
than a 16 gauge cord.  

(See Table A.)

4.  When using more than one extension cord 

to make up the total length, make sure 
each cord contains at least the minimum 
wire size required.  

(See Table A.)

5.  If you are using one extension cord for more 

than one tool, add the nameplate

 

amperes 

and use the sum to determine the required 
minimum cord size.  

(See Table A.)

6.  If you are using an extension cord outdoors, make 

sure it is marked with the suffix “W-A” (“W” in 
Canada) to indicate it is acceptable for outdoor use.

7.  Make sure the extension cord is properly wired 

and in good electrical condition.  Always replace 
a damaged extension cord or have it repaired 
by a qualified electrician before using it.

8.  Protect the extension cords from sharp objects, 

excessive heat, and damp or wet areas.

TABLE A:  RECOMMENDED MINIMUM WIRE 

GAUGE FOR EXTENSION CORDS* (120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD 

LENGTH

25´

50´

75´ 100´ 150´

0 – 2.0

18

18

18

18

16

2.1 – 3.4

18

18

18

16

14

3.5 – 5.0

18

18

16

14

12

5.1 – 7.0

18

16

14

12

12

7.1 – 12.0

18

14

12

10

-

12.1 – 16.0

14

12

10

-

-

16.1 – 20.0

12

10

-

-

-

* Based on limiting the line voltage drop to five volts at 

150% of the rated amperes.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Содержание 56776





















Отзывы: