Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 138 / 288

Repair

Edge MAXX

7-6

Inlet Conveyor Drive Belt Tension

Adjustment

An inlet conveyor motor is located at each

station, near the top of the inlet conveyor

assembly. The inlet conveyor drive belt tension

adjustment point can be reached from the front

of the unit.

Required Tools

3/16” Allen key, 1/2”, 9/16” wrenches

Perform only when the unit is OFF

with power disconnected.

Turn power OFF at the main disconnect

switch.

Remove the bolts that hold that station’s

inlet conveyor motor cover in place and

move the cover (Figure 7-5, A) so that the

inlet belt (B) can be seen.

Loosen the nuts which secure the inlet con-

veyor motor in position (Figure 7-5, C).

Pull the motor toward you to increase ten-

sion on the drive belt.

Make sure the pulleys are properly aligned

and tighten the bolts to secure the motor

in position.

Replace the inlet conveyor drive motor

cover.

WARNING

Never operate the unit unless

all safety covers are in place

and all safety equipment is

working correctly.

Start the unit to check the adjustment.

Figure 7-5: The bolts which secure the inlet motor

in position are in slotted holes.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды