Chery S18D Скачать руководство пользователя страница 2

Страница: 2 / 69

Chery S18D Service Manual

Contents

Chapter I Engine Hood & Luggage Boot

................................................................................................

I. Removal and Installation of Engine Hood

........................................................................................................

1. Preparations

..............................................................................................................................................

2. Precautions

................................................................................................................................................

3. Removal and Installation of Engine Hood Accessories

...........................................................................

4. Removal & Adjustment of Engine Hood Assembly

.................................................................................

5. Removal of Engine Hood Lock

................................................................................................................

6. Removal & Adjustment of Hood Cable

...................................................................................................

II. Removal and Installation of Trunk lid

.............................................................................................................

1. Preparations

..............................................................................................................................................

2. Removal of Trunk lid Trim Board

............................................................................................................

3. Removal and Installation of Luggage boot Lock

.....................................................................................

4. Removal of Luggage Boot Lock Cylinder

...............................................................................................

5. Removal of Rear Wiper Nozzle

................................................................................................................

6. Removal of Rear Wiper Motor

.................................................................................................................

Chapter II Removal of Interior Trim Parts

..............................................................................................

I. Removal and Installation of Seat Belts

.............................................................................................................

1. Preparations

..............................................................................................................................................

2. Precautions

................................................................................................................................................

3. Removal and Installation of the Seat belt of Front Seats

.........................................................................

4. Removal and Installation of the Seat belt of Rear Seats

.......................................................................

II. Removal and Installation of Seats

..................................................................................................................

1. Preparations

.............................................................................................................................................

2. Removal of Front Seats

..........................................................................................................................

3. Removal of Rear Seats

...........................................................................................................................

4. Installation Procedure

.............................................................................................................................

III. Removal and Installation of Central Console

..............................................................................................

1. Preparations

............................................................................................................................................

2. Removal Procedure

.................................................................................................................................

3. Installation Procedure

.............................................................................................................................

IV. Removal and Installation of Carpet

..............................................................................................................

1. Preparations

............................................................................................................................................

2. Removal Procedure

.................................................................................................................................

3. Installation Procedure

.............................................................................................................................

Chapter III Removal & Maintenance of Vehicle Doors

........................................................................

I. Removal, Installation & Maintenance of Front Doors

....................................................................................

1. Preparations

............................................................................................................................................

2. Precautions

..............................................................................................................................................

3. Removal Procedure

.................................................................................................................................

4. Installation Procedure

.............................................................................................................................

II. Removal & Installation of Rear Doors

..........................................................................................................

1. Preparations

............................................................................................................................................

2. Precautions

..............................................................................................................................................

3. Removal Procedure

.................................................................................................................................

4. Installation Procedure

.............................................................................................................................

Chapter IV Removal, Installation & Maintenance of Front/Rear Bumper

.........................................

Содержание S18D






































































Результаты поиска

Содержание S18D

Отзывы:

Chery S18D, Руководство по обслуживанию, Страница: 2 / 69

Результаты поиска

Содержание S18D

Отзывы: