background image

 

Adding and Configuring the G1104-8-6T Gateway

 

 

If this CheckVideo device will be monitored by a central station, please contact the central station for a username and 

password on their existing CheckVideo account. The central station will add the device to their account. 

The following items can be found within the box: 

 

G1104-8 channel Gateway 

 

Gateway power supply 

 

Terminal blocks for digital I/O 

 

Items not included: 

 

CheckVideo IP Camera Validation tool (found at 

www.checkvideo.com/support) 

 

A display monitor with HDMI cable 

 

Mouse for local display 

 

The Gateway has connectors on both sides.  The primary connectors are found on the back panel.  

 

To install the Gateway, make the following connections to the Gateway: 

 

Ethernet cable to the router.  

Note: Do not connect the CV4IP to a POE port on a router/switch. Power is 

provided by the included power supply. Providing power via a POE port to the WAN connection on the device 

will damage the Gateway.

 

 

HDMI supported monitor to Gateway 

 

Provided power supply to power outlet 

If you plan to use a local monitor, make sure that it is plugged in to the Gateway before it is powered up. With the 

monitor connected, the Gateway 

will display the “awaiting configuration from portal” message. 

 You will see this image 

on the screen until the device is added to the CheckVideo portal. 

Содержание G1104-8-6T









Отзывы: