Check Point Smart-1 150 Скачать руководство пользователя страница 35

Страница: 35 / 45

Customer Replaceable Parts

Smart-1 Hardware

Page 35

Removing the Power Supply

To remove a power supply unit:

1. If the power supply alarm sounds, press the red alarm button to the right of the power supply. This will

stop the alarm.

2. Remove the power cord.

3. Loosen the retaining screw located above the power socket.

4. Pull the extraction handle to remove the power supply unit.

Note

- Use only the extraction handle to remove the power supply unit. To

prevent damaging the power supply, do not pull on the retaining screw,
power cord clip or any other part of the unit.

Installing the Power Supply

To install a replacement power supply:

1. Insert the power supply into its slot and push firmly until it clicks into place.

2. Tighten the retaining screws.

3. Insert the power cord.

Hard Disk Drives

Smart-1 50 contains 4 hot-swappable redundant hard disk drives (RAID 10).

Smart-1 150 can contain up to 12 hot-swappable hard disk drives.

Implemented by a dedicated LSI Logic RAID controller, Smart-1 performs RAID10 mirroring and striping
across all of the installed hard disk drives.

Use the

raidconfig

SecurePlatform command to perform basic maintenance and monitoring procedures on

your Smart-1 RAID array.

raidconfig

Description

Perform basic maintenance and monitoring procedures on the Smart-1 RAID array

Syntax

raidconfig [status / rebuild /extendstorage / extendfs /
alarmon / alarmoff]

Parameters

Parameter

Description

status

Shows the status of RAID controllers and virtual disks

rebuild

Rebuilds degraded volumes. Use this option after replacing
one or more disks in the RAID array, or if the

raidconfig

status

command indicates a drive is not online.

extendstorage

Use if additional hard drives have been added to a Smart-1
150 machine. See detailed instructions below.

extendfs

Use if additional hard drives have been added to a Smart-1
150 machine but the proper RAID configuration has already
been manually defined.

alarmon

Enables alarm sound.

alarmoff

Disables alarm sound.

Содержание Smart-1 150














































Результаты поиска

Содержание Smart-1 150

Отзывы:

Бренды по названию

Популярные бренды

Check Point Smart-1 150, Руководство по началу работы

Результаты поиска

Содержание Smart-1 150

Отзывы:

Бренды по названию

Популярные бренды