Chauvet SkyScan 4000 Скачать руководство пользователя страница 8

Страница: 8 / 14

SkyScan™ 4000 User Manual

1/30/2012 4:39 PM

FUSE

The fuse is located
inside this
compartment. Remove
using a Phillips #2
screwdriver.

Fuse Replacement

With a Phillips #2 screwdriver, unscrew the fuse holder from its housing. Remove the damaged fuse

from its holder and replace with exact same type fuse. Screw the fuse holder back in its place and

reconnect power.

Note: there are 4 fuses in this fixture, each located by

the corresponding lamp power switches

Mounting

O RI E NT AT I O N

This fixture may only be mounted in a standing, vertical position, provided there is adequate room for

ventilation and movement.

Note: this fixture MUST be positioned in an upright position to allow proper cooling,

ventilation, and IP rating!

RI G G I NG

It is important never to obstruct the fan or vents pathway. Adjust the angle of the fixture by loosening

both knobs and tilting the fixture. After finding the desired position, retighten both knobs.

•

When selecting installation location, take into consideration lamp replacement access and routine
maintenance.

•

For use in dry locations only!

Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.

Содержание SkyScan 4000















Результаты поиска

Содержание SkyScan 4000

Отзывы:

Похожие инструкции для SkyScan 4000

Бренды по названию

Популярные бренды

Chauvet SkyScan 4000, Руководство пользователя

Результаты поиска

Содержание SkyScan 4000

Отзывы:

Похожие инструкции для SkyScan 4000

Бренды по названию

Популярные бренды