background image

Safety Instructions 

 

 

Please read these instructions carefully, which includes important 
information about the installation, usage and maintenance of this 
product. 

 

 

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that 
they also receive this instruction booklet. 

 

Always make sure that you are connecting to the proper voltage, and that the line voltage you are 
connecting to is not higher than that stated on the decal or rear panel of the fixture. 

 

This product is intended for indoor use only!  

 

To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no 
flammable materials close to the unit while operating. 

 

The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent 
surfaces. Be sure that no ventilation slots are blocked. 

 

Always disconnect from power source before replacing fuse and be sure to replace with same fuse 
type and rating. 

 

Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use 
its carrying handles. 

 

Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher 
than this.  

 

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the 
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please 
contact the nearest authorized technical assistance center. Always use the same type spare parts. 

 

Never connect the device to a dimmer pack. 

 

Make sure the power cord is never crimped or damaged. 

 

Never disconnect the power cord by pulling or tugging on the cord. 

 

Avoid direct eye exposure to the light source while it is on.  

Caution! 

There are no user serviceable parts inside the unit. Do not open the housing or 
attempt any repairs yourself. In the unlikely event your unit may require service, 
please contact CHAUVET at: 954-929-1115. 

 

 

 
 
 

 

 

 

Scorpion Sky User Manual 

2008-02-05/15:26

 

Содержание Scorpion Sky

















Отзывы: