background image

Mega Moon

™ User Manual 

9/16/2010 4:11 PM

 

Safety Instructions 

Please read these instructions carefully, which include important information about 
the installation, usage and maintenance of this product. 

 

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure 
that they also receive this instruction booklet. 

 

This product is for indoor use only! To prevent risk of fire or shock, do not expose fixture to rain 
or moisture. 

 

Make sure there are no flammable materials close to the unit while operating. 

 

Secure fixture to fastening device using a safety chain. 

 

Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate the fixture at temperatures 
higher than this.  

 

In the event of a serious operating problem, stop using the unit immediately. Never try to repair 
the fixture by yourself. Repairs carried out by unskilled people can lead to damage or 
malfunction. Please contact the nearest authorized technical assistance center. 

 

Make sure the power cord is not crimped or damaged. 

 

Never disconnect the power cord by pulling or tugging on the cord. 

 

Avoid direct eye exposure to the light source while it is on.  

 

Do not daisy chain power to more than 37 units @ 120V. 

 
 

There are no user serviceable parts inside the unit. Do not open the housing or 
attempt any repairs. In the unlikely event that your unit may require service, please 
contact CHAUVET at 954-929-1115. 

 

 
 
 
 

2.

 

I

NTRODUCTION

 

Features 

 

6-channel DMX-512 LED beam effect 

 

Individual control of red, green, blue and white LEDs within each cluster (4 total) 

 

Adjustable strobe speed 

 

Built-in automated programs via DMX 

 

Built-in sound activated programs via master/slave or DMX 

 

Additional Features 

 

Razor-sharp rotating beams  

 

Additional power output: max 37 units @ 120V

 

 

Содержание Mega Moon















Отзывы: