background image

 
 

 
Scorpion™ GBC User Manual 

August 2011 

Non Interlocked Housing Warning 

 

 

 

  This unit contains high power laser devices internally.  

  Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation.  

  The laser power levels, accessible if the unit is opened, can cause instant blindness, skin 

burns, and fires. 

Laser Safety Notes 

 

 

 

STOP AND READ ALL THE LASER SAFETY NOTES BELOW 

 

 

Laser Light is different from any other light sources with which you may be familiar. The light 
from this product can potentially cause eye injury if not set up and used properly. Laser light is 
thousands of times more concentrated than light from any other kind of light source. This 
concentration of light can cause instant eye injuries, primarily by burning the retina (the light 
sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser beam, it 
can still potentially injure or blind you or your audience. Even very small amounts of laser light 
are potentially hazardous even at long distances. Laser eye injuries can happen quicker than 
you can blink. 

It is incorrect to think that because these laser entertainment products use high speed scanned 
laser beams, that an individual laser beam is safe for eye exposure. 

It is also incorrect to assume that because the laser light is moving, it is safe. This is not true. 
Nor, do the laser beams always move. Since eye injuries can occur instantly, it is critical to 
prevent the possibility of any direct eye exposure. In the laser safety regulation, it is not legal to 
aim Class IIIa lasers in areas where people can be exposed. This is true even if it is aimed 
below people’s faces, such as on a dance floor. 

 

 

Do not operate the laser without first reading and understanding all safety and 
technical data in this manual. 

 

Always set up and install all laser effects so that all laser light is at least 3 meters 
(9.8 feet) above the floor on which people can stand. See the “Proper Usage” section 
later in this manual. 

 

After set up, and prior to public use, test the laser to ensure proper function. Do not 
use if any defect is detected.  

 

Laser Light - Avoid Direct Eye Exposure. 

 

Do not point lasers at people or animals. 

 

Never look into the laser aperture or laser beams. 

 

Do not point lasers in areas where people can potentially be exposed, such as 
uncontrolled balconies, etc. 

 

Do not point lasers at highly reflective surfaces, such as windows, mirrors and shiny 
metal. Even laser reflections can be hazardous. 

 

Never point a laser at aircraft, as this is a US Federal offense. 

 

Never point un-terminated laser beams into the sky. 

 

Do not expose the output optic (aperture) to cleaning chemicals. 

 

Do not use laser if the laser appears to be emitting only one or two beams. 

 

Do not use the laser if the housing is damaged, open, or if the optics appear 
damaged in any way. 

 

Never open the laser housing. The high laser power levels inside of the protective 
housing can start fires, burn skin and will cause instant eye injury. 

 

Never leave this device running unattended. 

 

The operation of a Class IIIa laser show is only allowed if the show is controlled by a 
skilled and well-trained operator, familiar with the data included in this manual. 

 

The legal requirements for using laser entertainment products vary from country to 
country. The user is responsible for the legal requirements at the location/country of 
use. 

 

Always use appropriate lighting safety cables when hanging lights and effects 
overhead. 

Содержание Laser Pointer

























Отзывы: