Chauvet DMX-311X Скачать руководство пользователя страница 2

Introduction

Congratulations on the purchase of your new CHAUVET lighting effect. We are confident that you will be
pleased with your purchase.  To assist you with the care and use of this product we have prepared a short
guide.

General Setup

Before connecting this unit to the main power supply, you must first install the lamps. 

Installing Lamps

1) Locate and remove the Lamp Replacement Set Screws located at the bottom of the lens.
2) Locate two bulb sockets (Ceramic rectangles with 2 holes in each)
3) Remove bulbs from packages, being careful not to touch them with your fingers.  Use  a napkin 

or other clean cloth instead.

4) Place the two prongs on each bulb into the corresponding holes located in the bulb socket.

Apply pressure to get the bulb to seat correctly in the holes.

5) Once both bulbs are in, close cover and replace cover set screws.

This lighting effect has been designed to function on a main power supply of 120V~60Hz or  230V~50Hz and
has been fitted with a suitable power plug.  The unit is equipped with a switchable power supply located on
the right hand side of the unit, check the voltage selector switch and verify it is set correctly for your local
voltage.

The Kinta (DMX-311X) is a one-channel DMX fixture that can be blacked out with the 
complimentary CH-X controller or programmed with Chauvet's DMX-6, DMX-40, DMX-50, ShowXpress Plus,
X-Factor, or any other universal DMX controller. 

Stand Alone

To operate in stand alone mode

 set only dipswitch # 1 to ON.

 Just plug it in and it will react to sound

.

To stop movement but maintain flashing, set all dipsqitches to OFF.

Linkable Mode

To operate in Linkable mode, you must link the units together using a premium quality 3-pin DMX cable in

the following configuration. "Out" from the first unit to "In" on the second, "Out" from the second unit to "In"
on the third,  and so on. The first unit must have dip switch (10) in the ON position. The
rest of the units must have all dip switches in the OFF position.

At Rear

¥DMX In

¥DMX Out

¥Microphone

¥Remote Input

¥Voltage Selector Switch

¥Dip Switches

¥ Complimentary 

blackout controller

Front

¥ Hanging bracket

¥Lamp Replacement

Cover Set Screws

Содержание DMX-311X

Страница 1: ...rld wide Headquarters 3000 North 29th Ct Hollywood FL USA 33020 Tel 1 954 929 1115 Fax 1 954 929 5560 www ChauvetLighting com KINTA DMX 311X User Guide Please read these instructions carefully before use ...

Страница 2: ...with a suitable power plug The unit is equipped with a switchable power supply located on the right hand side of the unit check the voltage selector switch and verify it is set correctly for your local voltage The Kinta DMX 311X is a one channel DMX fixture that can be blacked out with the complimentary CH X controller or programmed with Chauvet s DMX 6 DMX 40 DMX 50 ShowXpress Plus X Factor or an...

Страница 3: ...AUVET o ffers a range of items which are ideal for safe mounting Mount the Kinta in a well ventilated area without obstruction to the fan or vents to prevent damage from overheating DMX512 Control Value Rotating Direction Speed Step per second 0 Counterclockwise 0 step sec 2 24 Counterclockwise 60 stp sec 25 50 Counterclockwise 40 stp sec 51 76 Counterclockwise 24 stp sec 77 102 Counterclockwise 1...

Страница 4: ... fuse holder cover to reveal the fuse 3 Remove the old fuse 4 Place new fuse inside the holder Notes on fuses see below 5 Screw the fuse holder cover back on Notes on fuses This unit has a label attached which indicates the correct fuse rating If needed you can also find this listed as part of the specifications for the unit later in this guide It is critical that replacement fuses are of the corr...

Отзывы: