manualshive.com logo in svg

Chauvet Professional F4XIP, Руководство пользователя

Поделиться
Скачать
Chauvet Professional F4XIP Скачать руководство пользователя страница 6

2

 Before You Begin

F4XIP User Manual Rev. 1

Safety Notes

Read all the following safety notes before working with this product. These notes contain important 

information about the installation, usage, and maintenance of this product.

Personal Safety

•

Always disconnect the product from the power source before cleaning.

•

Always connect the product to a grounded circuit to avoid the risk of electrocution.

•

Do not touch the product’s housing when operating because it may be very hot.

Mounting and Rigging

•

WARNING: This product should only be used by competent and qualified persons.

•

DO NOT submerge this product (IP65). Temporary outdoor operation is fine.

•

When using this product in an outdoor environment, use IP65 (or higher) rated power and data 

cables. Be sure to secure unused power and data ports with attached IP65 covers.

•

CAUTION: When transferring product from extreme temperature environments, (e.g. cold truck to 

warm humid ballroom) condensation may form on the internal electronics of the product. To avoid 

causing a failure, allow product to fully acclimate to the surrounding environment before connecting 

it to power.

•

Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent 

surfaces.

•

Make sure there are no flammable materials close to this product while it is operating.

•

Never carry the product by the power cable or any moving part.

Power and Wiring

•

Make sure the power cable is not crimped or damaged.

•

Always make sure the product is being connected to the proper voltage in accordance with the 

specifications in this manual or on the product’s specification label.

•

To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely 

disconnect the product from power via breaker or by unplugging it.

•

Never connect this product to a dimmer pack or rheostat.

•

Never disconnect this product by pulling or tugging on the power cable.

Operation

•

Do not operate this product if there is damage on the housing, lenses, or cables. Have the damaged 

parts replaced by an authorized technician at once.

•

Do not cover the service module when operating to avoid internal overheating.

•

Operating Temperature: -4 °F to 104 °F (-20 °C to 40 °C)

•

In the event of a serious operation problem, stop using this product immediately!

Expected LED Lifespan

Over time, use and heat will gradually reduce LED brightness. Clustered LEDs produce more heat than 

single LEDs, contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 

40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit 

the overall intensity.

This product contains no user-serviceable parts. Any reference to servicing in this User 

Manual will only apply to properly trained, certified technicians. Do not open the housing 

or attempt any repairs.

All applicable local codes and regulations apply to proper installation of this product.

If your Chauvet product requires service, contact Chauvet Technical Support. 

Содержание F4XIP










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды