manualshive.com logo in svg

Charlton & Jenrick PARAGON FOCUS 18 HE, Руководство пользователя, Страница: 23 / 32

Поделиться
Скачать
Charlton & Jenrick PARAGON FOCUS 18 HE Скачать руководство пользователя страница 23

 

 

www.charltonandjenrick.co.uk 

23 

LT5558 (ISS 7) 

Method 2 (CABLE FIXING SYSTEM) 

 

Using a No 14 masonry bit drill two holes in the rear wall within the range shown, fit rawl plugs provided and 
screw eyebolts securely into plugs. 

 

Remove paper back from length of seal around the rear flange of the fire. 

NOTE: -The seal must be positioned to ensure an airtight seal when the appliance is fitted. 

 

Position the fire close to fireplace, allowing sufficient access to thread the cable through the eyebolts. Feed the 
cables (one cable to each side) through the top holes in the firebox, through the eyebolts, and back through the 
bottom holes in the firebox as shown. 

 

Push firebox fully back in the fireplace opening, allowing it to seal against it to seal against the surround. 

 

Feed the cables through the adjusters and cable clamps and 
slide the clamps up the adjusters.  Pull the cable as tight as 
possible and tighten the cable clamps. With a spanner 
tighten up the adjuster nut to tension the cable and make 
good the seal. 

Note: -After fitting neatly coil up the excess cable. Do not cut 
off the excess cable. 

 

 

 

 

 

SECTION TEN Checking Operation of Fire (installation instructions) 

 

CHECKING GAS SOUNDNESS  

 

 

Turn on the gas supply to the appliance and check for soundness in accordance with current codes of practice. 

 

Turn off the gas supply at the external Isolation valve. 

 

Remove the pressure test point screw from the inlet elbow and connect the pressure gauge. 

 

Turn on the gas to the appliance at the Isolation valve. 

 

Rotating the control to the ignition position and push in to allow the air in the pipe to be purged. 

 

Rotating the control knob a few times, check that the electrode is sparking at the gap between the 
thermocouple tip and the electrode; continue until pilot ignition is established. 

 

Depress the control knob slightly and rotate anticlockwise until the raised pointer is aligned with the large flame 
symbol on the control panel. 

 

Check the inlet pressure is Natural gas 20mbar. +/- 1.0 . 

 

Turn off gas supply, at the isolation valve. Disconnect the pressure gauge and replace the pressure test point 
screw. 

 

Turn on the supply to the appliance and check the pressure test point for soundness with detection fluid. 

 

Tensioning  

Screw 

Cable  

Clamp 

Содержание PARAGON FOCUS 18 HE

































Отзывы:

Нет отзывов