Charles 3653-36 Скачать руководство пользователя страница 12

Section 365–336–202

12

Table 4.  Frequency Response

FREQ (Hz)

XMT (dB)

RCV (dB)

60

Less than –14.0

––––––––

200

+0.15 to –2.0

+0.15 to –1.0

300

+0.15 to –0.15

+0.15 to –0.15

1000

0 (REF)

0 (REF)

3000

+0.15 to –0.15

+0.15 to –0.15

3400

0 to –1.5

0 to –1.5

4000

Less than –14.0

Less than –14.0

(j) CROSSTALK: 61dBm0 minimum at 400Hz; 71dBm0 minimum at 700Hz to 1KHz; 70dBm0 minimum

at 3kHz.

(k) LEVEL TRACKING SINGLE-ENDED AT 1020Hz: +0.25dB from +3 to –37dBm0, +0.5dB from –38 to

–50dBm0.

12.2.3. Loopback

(l) DETECTOR FREQUENCY: Will detect within 2713 + 7Hz; will not detect outside of 2713 + 35Hz.

(m) DETECTOR AMPLITUDE: Will detect 0.0  to –30dBm0; will not detect less than –40dBm0.

(n) DETECTOR TIMING: Activate, 2.2 seconds; deactivate, 1.1 seconds.

(o) ELL GAIN/ATTENUATION RANGE: 0.0 to 31.5dB in 0.5dB increments.

12.3

Physical Specifications

The physical characteristics of the 3653–36 4W are shown in Table 5.

Table 5.  

Physical Specifications

Feature

U.S.

Metric

Height

4.25 inches

10.8 centimeters

Width

1.31 inches

3.3 centimeters

Depth

10.31 inches

26.2 centimeters

Weight

9.25 ounces

263 grams

Temperature

32 to 122

 F

0 to 50

 C

Humidity

To 95% (no condensation)

    

Содержание 3653-36













Отзывы: