background image

Preparing and Using Your Silver Smoker

Before cooking with your Silver Smoker, the following steps should be closely followed to both cure the finish and 
season the interior steel.  Failure to properly follow these steps may damage the finish and/or impart metallic flavors 
to your first foods.

1. Brush all interior surfaces including grills and grates with vegetable cooking oil.

2. Build a small fire on the fire grate, being sure not to lay coals against the walls.

3. Close door.  (Position butterfly damper and smokestack damper approximately at one quarter open.)  This burn  

should be sustained for at least two hours, the longer the better.  Then, begin increasing temperature by opening 
the butterfly damper and smokestack damper half-way and adding more charcoal.  Your Silver Smoker is now 
ready for use.

Rust can appear on the inside of your smoker.  Maintaining a light coat of vegetable oil on interior surfaces will aid in 
the protection of your unit.  Exterior surfaces of smoker may need occasional touch up.  We recommend the use of a 
commercially available black high temperature spray paint.  NEVER PAINT THE INTERIOR OF THE UNIT !

GRILLING

Wood is recommended, however charcoal or a combination of both may be used as the fuel source for grilling,  with 
the fuel source placed and ignited on the fire grate.  Do not build too large of a fire.  We recommend starting a fire 
with no more than 4 pounds of charcoal (approximately 60 briquets) and adding more as needed during cooking.  
After allowing the fire to burn down, place the cooking grills in the smoker.  Failure to read and follow instructions for 
lighting charcoal may result in serious personal injury and/or property damage.

GRILL MAINTENANCE

Frequency of cleanup is determined by how much your smoker is used.  Make sure coals are completely 
extinguished before cleaning inside of smoker.  Inside surfaces may be cleaned with a strong solution of detergent 
and water applied with a scrub brush.  Thoroughly rinse with water and allow to air dry before using again.

SMOKING AND SLOW COOKING

If using the Silver Smoker as a smoker or slow cooker, remove the cooking grill from the firebox and build your fire on 
top of the fire grate in the firebox.  Either charcoal or wood may be used, but wood is the recommended fuel for it’s 
rate of burn and the flavor it imparts to the food being cooked.  Most seasoned hardwoods are good for smoking 
such as hickory, mesquite, pecan, oak, and many other fruit woods.  The firebox will accommodate most split 
fireplace size logs (16”).  Bark should be avoided or burned off first as it contains a high acid content and imparts an 
acrid flavor.

After allowing the fire to burn down, close the doors and control the temperature and smoke with the dampers located 
on the firebox and atop the smokestack.  Smoke is contained within the chambers, which will reduce burn while 
imparting more smoke flavor.  Do not operate the Silver Smoker with temperatures exceeding 450 degrees in the 
smoker chamber.  Place the food in the smoker chamber and monitor the temperature.  Cooking and smoking are 
taking place using indirect heat.  There is no need to worry about a grease fire flare-up ruining the food.  Do not place 
food within 6” of the opening from the firebox into the smoker chamber.  A general rule of thumb for cooking is about 
1 hour per pound for smoking large cuts of meat.  Refer to a cook book for specific cuts of meats.  Limit the number 
of times you open the smoker chamber door as this will allow heat to escape and extend the cooking time.

HELPFUL HINTS

•  If food seems to be getting too smoky or brown before the cooking time is finished, cover it loosely with heavy duty 

aluminum foil.

• Remove the ash after each use.

• Covered side dishes can be warmed in smoker chamber.

• To prevent flare-ups, brush meat lightly with oil before grilling.

• Keep a small squirt bottle of water handy for grilling flare-ups.

Содержание SILVER SMOKER 04201101

















Отзывы: